- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - OpenVMS
- >
- Problem with installing Data Protect 5.5 on OpenVM...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-11-2006 09:51 PM
тАО12-11-2006 09:51 PM
We have tried to install the DP5.5 in openVMS7.3-2 and we getting the following error.
%PCSI-E-EXESTAFAIL, product supplied EXECUTE START procedure failed
-CLI-W-IVVERB, unrecognized command verb - check validity and spelling
%PCSI-E-OPFAILED, operation failed
We use privilege user and binary FTP
Your help will be appreciated.
Thanks in advance.
Best regards,
Ashraf El Gabry
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-11-2006 10:30 PM
тАО12-11-2006 10:30 PM
Re: Problem with installing Data Protect 5.5 on OpenVMS 7.3-2
Pls. logout and login again any try to call the startup routine for the product manually.
regards Kalle
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-12-2006 12:56 AM
тАО12-12-2006 12:56 AM
Re: Problem with installing Data Protect 5.5 on OpenVMS 7.3-2
Data Protector assumes HP's TCP/IP Services is present and the start up procedure contains TCPIP commands.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-12-2006 05:59 AM
тАО12-12-2006 05:59 AM
Re: Problem with installing Data Protect 5.5 on OpenVMS 7.3-2
I would assume the product installed just fine. Try it out!
/Guenther
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-12-2006 08:53 PM
тАО12-12-2006 08:53 PM
Re: Problem with installing Data Protect 5.5 on OpenVMS 7.3-2
You can repeat the installation using the /TRACE qualifier of the PRODUCT INSTALL command. According to the help, this qualifier
"identifies DCL commands and command procedures that are run in a subprocess during the execution of the PRODUCT command. Any output from these commands is also displayed."
Hope this helps.
Regards.
Ana
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-27-2006 10:31 PM
тАО12-27-2006 10:31 PM
Re: Problem with installing Data Protect 5.5 on OpenVMS 7.3-2
We are using MultiNet V4.3 Rev A instead of UCX. As far as we understand from the OMNI$STARTUP.COM that it is using UCX command instead of the MultiNet stack. What is the equivalent commands for the MultiNet?
Best regards.
Ashraf
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-28-2006 03:36 AM
тАО12-28-2006 03:36 AM
Re: Problem with installing Data Protect 5.5 on OpenVMS 7.3-2
If you revealed what the commands are, you
might get more information back.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-02-2007 01:14 AM
тАО01-02-2007 01:14 AM
Solution$ multinet configure/server
MultiNet Server Configuration Utility Vn.n
[Reading in configuration from MULTINET:SERVICES.MASTER_SERVER]
SERVER-CONFIG>add omni
[Adding new configuration entry for service "OMNI"]
Protocol: [TCP]
TCP Port number: 5555
Program to run: OMNI$ROOT:[BIN]OMNI$STARTUP_INET.COM
[Added service OMNI to configuration]
[Selected service is now OMNI]
SERVER-CONFIG>sel omni
[The Selected SERVER entry is now OMNI]
SERVER-CONFIG>set flag ucx_server
[OMNI flags set to
SERVER-CONFIG>sho omni
Service Proto Port Action
------- ----- ---- ------
OMNI TCP 5555 Run Program OMNI$ROOT:[BIN]OMNI$STARTUP_INET.COM
SERVER-CONFIG>sho omni/full
Service "OMNI":
TCP socket (AF_INET,SOCK_STREAM), Port 5555
Socket Options = SO_KEEPALIVE
Flags = UCX_SERVER
INIT() = TCP_Init
LISTEN() = TCP_Listen
CONNECTED() = TCP_Connected
SERVICE() = Run_Program
Program = "OMNI$ROOT:[BIN]OMNI$STARTUP_INET.COM"
SERVER-CONFIG>write
SERVER-CONFIG>exit
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-03-2007 02:03 AM
тАО01-03-2007 02:03 AM
Re: Problem with installing Data Protect 5.5 on OpenVMS 7.3-2
Thanks a lot for all of you and special thanks to Richard Whalen. The Data Protected now installed in our Open VMS server. The thread now is closed.
Best regards.
Ashraf El Gabry
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-03-2007 02:06 AM
тАО01-03-2007 02:06 AM