- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - OpenVMS
- >
- Switch LAT to different Card
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-22-2007 11:52 PM
тАО02-22-2007 11:52 PM
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-23-2007 12:08 AM
тАО02-23-2007 12:08 AM
Re: Switch LAT to different Card
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-23-2007 12:16 AM
тАО02-23-2007 12:16 AM
Re: Switch LAT to different Card
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-23-2007 12:36 AM
тАО02-23-2007 12:36 AM
Re: Switch LAT to different Card
see the LATCP section in the System Management Utilities manual (http://h71000.www7.hp.com/doc/83final/6048/6048pro_039.html#startsubcommand_229 ):
CREATE LINK /DEVICE
If you enter the CREATE LINK command without the /DEVICE qualifier, LATCP attempts to find an available controller by using a list of possible LAT data link device names. HP recommends that you specify a default device name by defining the LAT$DEVICE logical name.
HTH,
Martin
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-23-2007 01:40 AM
тАО02-23-2007 01:40 AM
Solution$! ------------------------- Start LAT Protocol -----------------------------
$!
$! *** NOTE ***
$! If you have a system with multiple Ethernet/FDDI controllers, you may want
$! to create a link in this section of LAT$SYSTARTUP.COM before LAT is
$! started.
$!
$! When LAT is started on a system with multiple controllers, and no link is
$! is created, then the LAT driver will pick the first controller from the
$! LAN Data Structures as the default. This controller may not be connected to
$! the wire. LTDRIVER has no way of determining this condition. As a result,
$! it will not display an error message and LAT will hang.
$!
$! To define a link for LAT, do the following:
$! 1. Find out what controller is attached to the Ethernet/FDDI wire.
$! (In this example we will use EXA0)
$! 2. Insert the following command line before LCP SET NODE /STATE=ON command
$! below:
$!
$! LCP CREATE LINK 1ST$LINK /DEVICE=EXA0
$!
$! 3. If you have more then one controller attached to the wire, then
$! repeat the above command line, calling the next controller "2ND$LINK".
$! i.e. -
$! LCP CREATE LINK 1ST$LINK /DEVICE=EXA0
$! LCP CREATE LINK 2ND$LINK /DEVICE="xxx0"
$!
$! Where, xxx0 is the next controller attached to the wire
$! ...
$! etc
$!
$ lcp set node /state=on
Love it when Engineering puts comments inside the DCL command procedures themselves :-)
Verne
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-23-2007 01:52 AM
тАО02-23-2007 01:52 AM
Re: Switch LAT to different Card
How about defining the logical LAT$DEVICE ?
Greetz,
Kris (aka Qkcl)
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-23-2007 02:43 AM
тАО02-23-2007 02:43 AM
Re: Switch LAT to different Card
Put
$ LCP CREATE LINK 1ST$LINK /DEVICE=EWB0
before
$ lcp set node /state=on
in SYS$STARTUP:LAT$SYSTARTUP:COM
and it will work.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-23-2007 02:46 AM
тАО02-23-2007 02:46 AM
Re: Switch LAT to different Card
you can do all this by using explicit LATCP> CREATE LINK commands, but the simplest solution for moving LAT from EWA to EWB is:
$ DEFINE/SYSTEM LAT$DEVICE EWB
before invoking LAT$STARTUP
Volker.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-23-2007 03:09 AM
тАО02-23-2007 03:09 AM