- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - OpenVMS
- >
- Re: UCX won't startup automatically.
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-20-2004 03:32 AM
тАО02-20-2004 03:32 AM
Whenever I reboot the system I have to manually execute the command. @sys$manager:ucx$config, and start the TCPIP services. I uncommented the ! in systartup_vms.com to execute @sys$manager:startnet.com. I am running on Decnet Phase_IV V7.3
What else is wrong??
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-20-2004 03:47 AM
тАО02-20-2004 03:47 AM
Solutionlocate the following section in systartup_vms.com
$! Remove the comment delimiter ($!) from the following line to start
$! versions of Digital TCP/IP Services for OpenVMS beginning with V5.0.
$!
$ @SYS$STARTUP:TCPIP$STARTUP.COM
Remove the comment as indicated (and as it has been done in the example above).
HTH, Martin
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-20-2004 04:12 AM
тАО02-20-2004 04:12 AM
Re: UCX won't startup automatically.
I think you're using UCX V4.xx (because you wrote have do type @sys$manager:ucx$config) so comand to insert in SYS$SYSTARTUP_VMS.COM is @SYS$STARTUP:UCX$STARTUP.COM
You could be sure of your version so it's better type
$ UCX SHOW VERSION
if you have V4.xx it's good use UCX$STARTUP, if you have V5.xx it's better use TCPIP$STARTUP and TCPIP$CONFIG to configure.
H.T.H.
Antoniov
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-20-2004 05:49 AM
тАО02-20-2004 05:49 AM
Re: UCX won't startup automatically.
there is a ucx$config.com also on V5. It does invoke tcpip$config.com actually.
Greetings, Martin
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-20-2004 07:01 PM
тАО02-20-2004 07:01 PM
Re: UCX won't startup automatically.
I know this one; HP has released old command UCX$* that call TCPIP$* to compatibility with older version of software; this's made to permit gradually change of configuration; leaving UCX* command may meet some problem in future version so it's better use current command in SYSTARTUP_VMS.COM.
Bye
Antoniov