- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - OpenVMS
- >
- Re: decnet loop issue
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-22-2006 01:39 PM
тАО05-22-2006 01:39 PM
mc ncp
ncp>loop node ***
%NCP-W-MIRCTF, Mirror connect failed , Access control rejected
Messages not looped = 1
so i telnet to that server and do the loop testing to my vax server, no problem. but loop itself the same problem:%NCP-W-MIRCTF, Mirror connect failed , Access control rejected
Messages not looped = 1
What is the problem ? Is it caused by mirro$server settings?
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-22-2006 01:49 PM
тАО05-22-2006 01:49 PM
Solutionwelcome to the OpenVMS ITRC forum.
The NCP LOOP application will connect to the MIRROR object or MIRROR session control application on the destination node. If it can't connect to that application due to missing username/password information, you'll see this error message.
Check the following on the destination node:
MC NCP SHOW OBJ MIRROR (DECnet Phase IV) or
MC NCL SHOW SESS CONT APPLIC MIRROR ALL (DECnet-Plus)
DECnet Phase IV needs a valid username/password, which matches the entry in SYSUAF.
DECnet-Plus just needs a valid username.
Volker.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-22-2006 02:02 PM
тАО05-22-2006 02:02 PM
Re: decnet loop issue
Yes , my decnet version is IV. and i also used: loop node xxx password xxx user xxx. and it was ok. But actually, there 2 vax servers that buildup a cluster. I used loop node xxx to both of the 2 servers. One is ok , but the other is not ok. They have the same decnet version, and the same uaf. So i am not clear about it.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-22-2006 04:30 PM
тАО05-22-2006 04:30 PM
Re: decnet loop issue
Are there any additional messages in operator.log or audit log about the failed connect?
Purely Personal Opinion
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-22-2006 05:44 PM
тАО05-22-2006 05:44 PM
Re: decnet loop issue
yes, they have the same system disk and the same sysuaf. the obj define seems the same.when i use loop node xxx on that vax server to loop itself , it displays the same error message:%NCP-W-MIRCTF, Mirror connect failed , Access control rejected
Messages not looped = 1
but loop other node on that server, it is ok.(include looping its cluster member)
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-22-2006 08:38 PM
тАО05-22-2006 08:38 PM
Re: decnet loop issue
I believe this is the 'classic' DECnet object password problem in a cluster with a shared SYSUAF file.
Please check, whether MC NCP SHOW OBJ MIRROR (with privileges turned on), shows the SAME password on both nodes !
DECnet Phase IV generates 'unique' passwords for some of it's DECnet objects during @NETCONFIG. It does so for each node you configure on your shared system disk, but the password of the second node you're configuring overwrites the password for the first node in SYSUAF.
Once you've found that the passwords are different, use the password from the 'working' (remote) node and use MC NCP DEF OBJ MIRROR PASS xxx on the failing (remote) node and then reload the object mit MC NCP SET OBJ MIRROR ALL
Volker.