- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - OpenVMS
- >
- Re: setup network on Openwms 8.3 Integrity
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-04-2011 11:11 PM
тАО04-04-2011 11:11 PM
thank you in advance
P.S. (DecNet installed )
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-04-2011 11:30 PM
тАО04-04-2011 11:30 PM
SolutionPlease refer the below document for configuring the telnet.
http://h71000.www7.hp.com/doc/83final/ba554_90008/ch02s08.html
Refer the below link for documentation on TCP/IP services for VMS.
http://h71000.www7.hp.com/doc/tcpip57.html
Regards,
Ketan
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-05-2011 04:17 AM
тАО04-05-2011 04:17 AM
Re: setup network on Openwms 8.3 Integrity
@startup:tcpip$config
Setup core and client+server serivces TELNET.
You probably want to enable the DTP service also.
If you are just telnetting to the box, there is no need for route/bind/ntp and other trimmings.
You already have DECnet going, but be aware of a surprise to some is that you always have to start decnet before $startup:tcpip$startup.
(because DECnet fudges the MAC address).
Good luck,
Hein
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-05-2011 04:20 AM
тАО04-05-2011 04:20 AM
Re: setup network on Openwms 8.3 Integrity
Step 1: Check for Network interfaces
$ show dev ew (should give something like)
Device Device Error
Name Status Count
EWA0: Online 0
EWB0: Online 0
$ show dev ewa/full
Device EWA0:, device type BCM5704, is online, network device, error logging is
enabled, device is a template only.
Error count 0 Operations completed 0
Owner process "" Owner UIC [SYSTEM]
Owner process ID 00000000 Dev Prot S:RWPL,O:RWPL,G,W
Reference count 0 Default buffer size 512
Current preferred CPU Id 0 Fastpath 1
Current Interrupt CPU Id 0
Operating characteristics: Link up, Full duplex.
Speed (Mbits/sec) 1000
Def. MAC addr 00-17-A4-77-10-18 Current MAC addr AA-00-04-00-02-08
Notice: Operating characteristics: Link Up, Full Duplex, (and below) Speed 1000Mb/s.
-----------------------
If Link is not up then you need to fix that first
-----------------------
OK So far. Now run TCPIP$CONFIG
$ @sys$manager:tcpip$config
Select Option 1 (Core)
Next menu, Select Option 1 (Domain)
-> Enter your domain name.
Same menu, Select Option 2 (Interfaces)
-> assign your IP address to the interface of your choice.
(Note: WE0=EWA0, WE1=EWB0, WE2=EWC0, etc.)
Return to first menu.
Select Option 2 (Client Options)
Next menu Select Option 8 (TELNET)
Select option to Start and Enable Service on this Node.
Return to first menu. EXIT.
Should be done.
Dave.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-05-2011 10:08 PM
тАО04-05-2011 10:08 PM