- Community Home
- >
- Servers and Operating Systems
- >
- Legacy
- >
- Operating System - Tru64 Unix
- >
- Re: Adding KZPCC to ES40 with Digital Unix 4.0G
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-29-2009 03:09 AM
07-29-2009 03:09 AM
we are in a phase of adding new storage to our server ES40. We installed KZPCC with 2 HDDs 146G, the Two HDD configured as RAID 1, and can be shown on the P00>>show dev as dza516 (BSA).
But when booting the OS, it is not detected by the OS.
Please advice.
Note: attached is the boot log file
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-29-2009 12:07 PM
07-29-2009 12:07 PM
Re: Adding KZPCC to ES40 with Digital Unix 4.0G
Take a look through the following page:
http://h18002.www1.hp.com/alphaserver/options/ases40/ases40_ds-kzpcc-ce.html
Looking at your boot log, you need to upgrade your firmware to at least 5.8. You're currently on 5.7. You also need to be on at least patck kit 3.
Hope this helps,
Regards,
Rob
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-29-2009 11:16 PM
07-29-2009 11:16 PM
Re: Adding KZPCC to ES40 with Digital Unix 4.0G
>>>
Jul 24 13:51:28 es40 vmunix: xcr0 at pci1 slot 5
Jul 24 13:51:28 es40 vmunix: re0 at xcr0 unit 0 (unit status = ONLINE, raid level = 5)
Jul 24 13:51:28 es40 vmunix: (WRITE BACK cache operation SUPPORTED if battery backup enabled)
Jul 24 13:51:28 es40 vmunix: re1 at xcr0 unit 1 (unit status = ONLINE, raid level = 5)
Jul 24 13:51:28 es40 vmunix: (WRITE BACK cache operation SUPPORTED if battery backup enabled)
<<<
did you run MAKEDEV to create the device special files?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-29-2009 11:24 PM
07-29-2009 11:24 PM
Re: Adding KZPCC to ES40 with Digital Unix 4.0G
Thanks for you reply, but we have two problems:
1- â ¦v4.0G:
â Patch Kit: T64V40GAS0003-20010613.tar required. See most up-to-date patch information.
How can we get this patch?
2- For any new hardware added to True 64 Unix, a kernel rebuild must be done to detect the new Hardware and install its drivers, what we know till now that we have to boot to genvmunix and do the kernel rebuild there, but we still need detailed steps how to do that without affecting the existing configuration especially there is an Oracle Database installed on this server.
Please advice
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-29-2009 11:28 PM
07-29-2009 11:28 PM
Re: Adding KZPCC to ES40 with Digital Unix 4.0G
the OS see an existing RAID controller, and not the new one, the new one must shown as:
i2o0 at slot 4 (since we install it on slot 4)
I think the Kernal rebuild will solve our issue, so please help us in that.
Thanks
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-29-2009 11:42 PM
07-29-2009 11:42 PM
Solutionsorry for the mistake.
procedure would be
boot general unix kernel
>>> boot -fi genvmunix
use sizer to detect hardware and create a new configfile
unix# sizer -v > /tmp/newsystem.conf
- compare this file with the current configfile in /sys/conf
diff /tmp/newsystem.conf /sys/conf/
- some line (probably "config_driver itpsa") will differ
- add this line to the /sys/conf/
and do a "doconfig -c"
- make a backup of your old vmunix "cp /vmunix /vmunix.old"
- and copy the new vmunix to the root of the filesystem "cp /usr/sys/
- reboot to the new kernel
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-31-2009 06:03 AM
07-31-2009 06:03 AM
Re: Adding KZPCC to ES40 with Digital Unix 4.0G
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-31-2009 06:05 AM
07-31-2009 06:05 AM
Re: Adding KZPCC to ES40 with Digital Unix 4.0G
Thanks again Pieter
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-31-2009 06:09 AM
07-31-2009 06:09 AM
Re: Adding KZPCC to ES40 with Digital Unix 4.0G
thanks for feedback and points
Regards,
Pieter