- Community Home
- >
- Servers and Operating Systems
- >
- Legacy
- >
- Operating System - Tru64 Unix
- >
- Re: B-Cache not detected after power outage
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-27-2005 03:33 AM
тАО04-27-2005 03:33 AM
B-Cache not detected after power outage
After a building wide power outage had been corrected, one of the systems gives a beep code on power up, and the SROM reports 'detected system configuration error'
Tru64 will boot, but reports 'no B-Cache detected'
Any ideas on whats gone wrong an how to fix it ?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-28-2005 07:37 AM
тАО04-28-2005 07:37 AM
Re: B-Cache not detected after power outage
Post the output of the console at power-up time. Post the output of:
>>> show config
>>> cat el
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-03-2005 01:38 AM
тАО05-03-2005 01:38 AM
Re: B-Cache not detected after power outage
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-03-2005 01:57 AM
тАО05-03-2005 01:57 AM
Re: B-Cache not detected after power outage
The error column in 'show FRU' output is non-zero for some of the memory dims, variously code 80 and 82.
I will attach the suggested info dumps and to a support call, but is there a way of capturing the output from 'cat el' and 'show config' onto a floppy disk, from the firmware prompt ?
(I don't like having to write all this stuff down !)
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-08-2005 08:44 PM
тАО05-08-2005 08:44 PM
Re: B-Cache not detected after power outage
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-03-2006 02:36 AM
тАО04-03-2006 02:36 AM