- Community Home
- >
- Servers and Operating Systems
- >
- Legacy
- >
- Operating System - Tru64 Unix
- >
- Installation problem - Tru64 5.1a on DS20E
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-22-2008 07:35 AM
тАО04-22-2008 07:35 AM
I've got NHD7 downloaded & burnt to a CD, followed the instructions in the download and the installation appears to run fine - until the reboot.
Once the server comes back up, it doesn't boot and gives the error:
halt code = 2
kernel stack not valid halt
According to the instructions, it's supposed to ask for the NHD kit location again - but it doesn't, I'm guessing this might have something to do with it?
I suppose my first question is, is this a supported configuration?
And if it is, does anyone have any ideas what might be up with it? I've got a suspicion it's an SRM variable wrong somewhere, but I'm not sure which ones I should be looking at!
I'm trying to install to a logical drive on a SmartArray 5300 controller if it helps.
Cheers
Ed
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-22-2008 11:19 AM
тАО04-22-2008 11:19 AM
Re: Installation problem - Tru64 5.1a on DS20E
nothing, but is this one of those wwidmgr
questions?
Has any of this kit worked together before,
or do you need to do the basic wwidmgr stuff
so that SRM can locate the fibrous disk(s)?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-22-2008 02:03 PM
тАО04-22-2008 02:03 PM
Re: Installation problem - Tru64 5.1a on DS20E
If its a SmartArray 5300 (aka KZPDC) then there shouldn't be any fibre or wwidmgr involved...
What does the output of "show boot*" give you from the SRM prompt (P00>>>)
Cheers,
Rob
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-22-2008 02:05 PM
тАО04-22-2008 02:05 PM
Solutionhttp://h18002.www1.hp.com/alphaserver/options/asds20e/asds20e_3x-kzpdc-be.html
Cheers,
Rob
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-22-2008 11:52 PM
тАО04-22-2008 11:52 PM
Re: Installation problem - Tru64 5.1a on DS20E
I've pulled the smart array out and successfully installed the server on a basic disk, so I assume the rest of the hardware is fine...
I'll post up the output of the 'show boot' command when I get there.
Cheers!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-23-2008 01:38 AM
тАО04-23-2008 01:38 AM
Re: Installation problem - Tru64 5.1a on DS20E
Moving the array controller to the bottom slot worked.
Thanks very much for your help!
Cheers
Ed
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-23-2008 01:43 PM
тАО04-23-2008 01:43 PM
Re: Installation problem - Tru64 5.1a on DS20E
Cheers,
Rob