Query about FC card in Tru64 5.1

[Neeraj Bajpai]

Hi All,

I am struggling with one FC(KGPSA-CA : Driver Rev 2.02 : F/W Rev 3.81A4(2.01A0)) card which is installed on Tru64 5.1 and connected to McData switch. I did the correct zoning on switch, but when I am checking the card by
# emxmgr -t emx7
emx7 state information:
Link : connection is UP (but PAUSED)
Point to Point
Fabric attached
FC DID 0x652313
Link is SCSI bus 9 (e.g. scsi9)
SCSI target id -1
portname is 1000-0000-C924-3142
nodename is 2000-0000-C924-3142
N_Port at FC DID 0xfffffc - SCSI tgt id -1 :
portname 2000-0800-8804-0BC9
nodename 1000-0800-8804-0BC9
Present, Logged in, Directory Server,
N_Port at FC DID 0xfffffe - SCSI tgt id -1 :
portname 2023-0800-8804-0BC9
nodename 1000-0800-8804-0BC9
Present, Logged in, F_PORT,
It display the info but card is "PAUSED". I can not see any storage port which I have assigned via zoning.

The other card is working fine
# emxmgr -t emx6
emx6 state information:
Link : connection is UP
Point to Point
Fabric attached
FC DID 0x662313
Link is SCSI bus 5 (e.g. scsi5)
SCSI target id -1
portname is 1000-0000-C924-3331
nodename is 2000-0000-C924-3331
N_Port at FC DID 0x661013 - SCSI tgt id 2 :
portname 5005-0763-00CF-B03E
nodename 5005-0763-00C0-B03E
Present, Logged in, FCP Target, FCP Logged in,
N_Port at FC DID 0x660413 - SCSI tgt id 3 :
portname 5005-0763-00C3-B03E
nodename 5005-0763-00C0-B03E
Present, Logged in, FCP Target, FCP Logged in,
N_Port at FC DID 0x660813 - SCSI tgt id 4 :
portname 5005-0763-00CB-B03E
nodename 5005-0763-00C0-B03E
Present, Logged in, FCP Target, FCP Logged in,
N_Port at FC DID 0xfffffc - SCSI tgt id -1 :
portname 2000-0800-88A0-A128
nodename 1000-0800-88A0-A128
Present, Logged in, Directory Server,
N_Port at FC DID 0xfffffe - SCSI tgt id -1 :
portname 2023-0800-88A0-A128
nodename 1000-0800-88A0-A128
Present, Logged in, F_PORT,
N_Port at FC DID 0x660c13 - SCSI tgt id 1 :
portname 5005-0763-00C7-B03E
nodename 5005-0763-00C0-B03E
Present, Logged in, FCP Target, FCP Logged in,

Is anyone knew about (but PAUSED) state of FC card.

Thanks in advance

[Mark Poeschl_2]

If you log in to the fibre channel switch and do a 'portshow ' where n is the port number your HBAs are plugged into what do you get? (assuming you're using Brocade switches)

[Mark Poeschl_2]

Oooops! My bad. I should read the whole message first ;-)