- Community Home
- >
- Servers and Operating Systems
- >
- Legacy
- >
- Operating System - Tru64 Unix
- >
- Re: Unable to boot 5.1B
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-05-2005 10:01 PM
тАО09-05-2005 10:01 PM
I cannot boot 5.1B on a customers system either from CD or from disk whenever the HSZ70 controller is powered on. I know there has been quite some debate about HSZ70's in the past:
http://forums1.itrc.hp.com/service/forums/questionanswer.do?threadId=640329
but it seems they are now supported.
The firmware on the DS20 has been upgraded as per the 6.9 Firmware CD and the internal KZPBA is at 5.77. The HSZ itself is at 77Z-0. Am I going to need patches to the HSZ to make it work?
The message I get on boot comes on discovery of scsi5, which is the location of the HSZ.
It cycles around each target:
ccfg_do_inq_ccb
It's basically saying its doing and inquiry and can't stat what its seeing I think.
Turn off the HSZ and it boots fine.
Any clues?
cheers,
Ian.
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-06-2005 05:25 PM
тАО09-06-2005 05:25 PM
Re: Unable to boot 5.1B
>>> sho dev
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-06-2005 11:55 PM
тАО09-06-2005 11:55 PM
Re: Unable to boot 5.1B
The HSZ70 is supported under 5.1b and you appear to have the right firmware versions, so you may want to engage support.
Did it ever work with 5.1B for you, or is this a new install? Did an older OS version work for you (which?)
An old (HP internal) note from Han suggests there may be a problem with HSZ70's if you are doing multibus failover with dual controllers. The vendor ID's on the two controllers are sometimes different (missing?), which confuses the operating system. m. This caused the WWID not to be unique. This cause a no match in DDR database for hwmgr to generate the right additions, and it goes down hill from there.
To check if you have this problem do a "show this" and "show other" on the HSZ70's. Make sure that the vendor/product ID's are identical (including white spaces and everything). You may have to swap the controller and make sure that the new ones are identical.
hth,
Hein.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-07-2005 06:53 AM
тАО09-07-2005 06:53 AM
Re: Unable to boot 5.1B
Hello Hein! I went to some of your sessions at the (sadly missed) Symposium!
The system itself is running 4.0F. I was checking that it would boot the 5.1B CD to make sure that my upgrade (via 5.0a) would work. I think you might be right about support...
cheers,
Ian.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-07-2005 06:54 AM
тАО09-07-2005 06:54 AM
Re: Unable to boot 5.1B
I will get the vendor ID information tomorrow.
thanks,
Ian.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-08-2005 03:02 AM
тАО09-08-2005 03:02 AM
Re: Unable to boot 5.1B
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-08-2005 09:30 PM
тАО09-08-2005 09:30 PM
Re: Unable to boot 5.1B
If so, is this the latest one? You may want to try booting from the NHD7 media as there were a few fixes for the HSZ70 in BL025. I don't see exactly your problem in the description, but you never know.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-09-2005 05:41 AM
тАО09-09-2005 05:41 AM
Re: Unable to boot 5.1B
I thought I had tried to boot NHD-7 but I will confirm on Monday as I have a site visit booked and some downtime arranged.
many thanks,
Ian.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-14-2005 03:12 AM
тАО09-14-2005 03:12 AM
Re: Unable to boot 5.1B
4.0F - April '99 - OK
5.1 - '00 - OK
5.1B - Nov '02 - FAILS
The full error messages are "invalid inquiry data received", "ccfg_do_inq_ccb" and "hard error detected". I'm going to log a call tomorrow.
cheers,
Ian.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-23-2005 09:28 PM
тАО10-23-2005 09:28 PM
Re: Unable to boot 5.1B
This has now moved on to me trying to patch the HSZ70! Does anyone know where I can find the HSZ70 patch kits?
cheers,
Ian.