alpha ra7000 disk failed ???

[mac2008_1]

alpha ra7000 disk failed , power failed ,help !!!
what can replace disk and POWER ?


MESSAGE:

Starting HSZterm Version V1.1A
Copyright Digital Equipment Corporation 1996. All rights reserved


Copyright Compaq Computer Corporation 1993, 1998. All rights reserved.
HSZ70 Firmware version V73Z-0, Hardware version H04

Last fail code: 018000A0

Press " ?" at any time for help.


Power Supply failure cleared.
Temperature is within optimum range.
HSZ70 > show storagesets full

Name Storageset Uses Used by
------------------------------------------------------------------------------

R1 raidset DISK10000 D0
DISK20000
DISK30000
DISK40000
DISK60100
Switches:
POLICY (for replacement) = BEST_PERFORMANCE
RECONSTRUCT (priority) = NORMAL
CHUNKSIZE = 256 blocks
State:
NORMAL
DISK10000 (member 0) is NORMAL
DISK20000 (member 1) is NORMAL
DISK30000 (member 2) is NORMAL
DISK40000 (member 3) is NORMAL
DISK60100 (member 4) is NORMAL
Size: 142190816 blocks

R2 raidset DISK10100 D100
DISK20100
DISK30100
DISK40100
Switches:
POLICY (for replacement) = BEST_PERFORMANCE
RECONSTRUCT (priority) = NORMAL
CHUNKSIZE = 256 blocks
State:
REDUCED
DISK10100 (member 0) is NORMAL
DISK20100 (member 1) is NORMAL
DISK30100 (member 2) is NORMAL
DISK40100 (member 3) is NORMAL
Size: 142190816 blocks

SPARESET spareset

FAILEDSET failedset DISK50000
DISK50100
DISK60000
Switches:
NOAUTOSPARE
Power Supply failure cleared.
Temperature is within optimum range.
HSZ70 > show raidset full

Name Storageset Uses Used by
------------------------------------------------------------------------------

R1 raidset DISK10000 D0
DISK20000
DISK30000
DISK40000
DISK60100
Switches:
POLICY (for replacement) = BEST_PERFORMANCE
RECONSTRUCT (priority) = NORMAL
CHUNKSIZE = 256 blocks
State:
NORMAL
DISK10000 (member 0) is NORMAL
DISK20000 (member 1) is NORMAL
DISK30000 (member 2) is NORMAL
DISK40000 (member 3) is NORMAL
DISK60100 (member 4) is NORMAL
Size: 142190816 blocks

R2 raidset DISK10100 D100
DISK20100
DISK30100
DISK40100
Switches:
POLICY (for replacement) = BEST_PERFORMANCE
RECONSTRUCT (priority) = NORMAL
CHUNKSIZE = 256 blocks
State:
REDUCED
DISK10100 (member 0) is NORMAL
DISK20100 (member 1) is NORMAL
DISK30100 (member 2) is NORMAL
DISK40100 (member 3) is NORMAL
Size: 142190816 blocks
Power Supply failure cleared.
Temperature is within optimum range.
HSZ70 > show units full

LUN Uses
--------------------------------------------------------------

D0 R1
Switches:
RUN NOWRITE_PROTECT READ_CACHE
WRITEBACK_CACHE
MAXIMUM_CACHED_TRANSFER_SIZE = 32
ACCESS_ID = ALL
State:
ONLINE to this controller
Reserved
PREFERRED_PATH = THIS_CONTROLLER
Size: 142190816 blocks
D100 R2
Switches:
RUN NOWRITE_PROTECT READ_CACHE
WRITEBACK_CACHE
MAXIMUM_CACHED_TRANSFER_SIZE = 32
ACCESS_ID = ALL
State:
ONLINE to this controller
Reserved
PREFERRED_PATH = THIS_CONTROLLER
Size: 142190816 blocks
Power Supply failure cleared.
Temperature is within optimum range.
HSZ70 > show devices full

Name Type Port Targ Lun Used by
------------------------------------------------------------------------------

DISK10000 disk 1 0 0 R1
COMPAQ BB01811C9C 3B05
Switches:
NOTRANSPORTABLE
TRANSFER_RATE_REQUESTED = 20MHZ (synchronous 20.00 MHZ negotiated)
Size: 35556389 blocks
DISK10100 disk 1 1 0 R2
COMPAQ BB01811C9C 3B05
Switches:
NOTRANSPORTABLE
TRANSFER_RATE_REQUESTED = 20MHZ (synchronous 20.00 MHZ negotiated)
Size: 35556389 blocks
DISK20000 disk 2 0 0 R1
COMPAQ BB01811C9C 3B05
Switches:
NOTRANSPORTABLE
TRANSFER_RATE_REQUESTED = 20MHZ (synchronous 20.00 MHZ negotiated)
Size: 35556389 blocks
DISK20100 disk 2 1 0 R2
COMPAQ BB01811C9C 3B05
Switches:
NOTRANSPORTABLE
TRANSFER_RATE_REQUESTED = 20MHZ (synchronous 20.00 MHZ negotiated)
Size: 35556389 blocks
DISK30000 disk 3 0 0 R1
COMPAQ BB01811C9C 3B05
Switches:
NOTRANSPORTABLE
TRANSFER_RATE_REQUESTED = 20MHZ (synchronous 20.00 MHZ negotiated)
Size: 35556389 blocks
DISK30100 disk 3 1 0 R2
COMPAQ BB01811C9C 3B05
Switches:
NOTRANSPORTABLE
TRANSFER_RATE_REQUESTED = 20MHZ (synchronous 20.00 MHZ negotiated)
Size: 35556389 blocks
DISK40000 disk 4 0 0 R1
COMPAQ BB01811C9C 3B05
Switches:
NOTRANSPORTABLE
TRANSFER_RATE_REQUESTED = 20MHZ (synchronous 20.00 MHZ negotiated)
Size: 35556389 blocks
DISK40100 disk 4 1 0 R2
COMPAQ BB01811C9C 3B05
Switches:
NOTRANSPORTABLE
TRANSFER_RATE_REQUESTED = 20MHZ (synchronous 20.00 MHZ negotiated)
Size: 35556389 blocks
DISK50000 disk 5 0 0 FAILEDSET
Misconfigured: No device at this PTL, please see user guide
DISK50100 disk 5 1 0 FAILEDSET
Misconfigured: No device at this PTL, please see user guide
DISK60000 disk 6 0 0 FAILEDSET
Misconfigured: No device at this PTL, please see user guide
DISK60100 disk 6 1 0 R1
COMPAQ BB01811C9C 3B05
Switches:
NOTRANSPORTABLE
TRANSFER_RATE_REQUESTED = 20MHZ (synchronous 20.00 MHZ negotiated)
Size: 35556389 blocks
Power Supply failure cleared.
Temperature is within optimum range.
HSZ70 > show failedset

Name Storageset Uses Used by
------------------------------------------------------------------------------

FAILEDSET failedset DISK50000
DISK50100
DISK60000
Switches:
NOAUTOSPARE
Power Supply failure cleared.
Temperature is within optimum range.
HSZ70 > show this full

Controller:
HSZ70 ZG93207867 Firmware V73Z-0, Hardware H04
Configured for dual-redundancy with ZG93207803
In dual-redundant configuration
Device Port SCSI address 7
Time: NOT SET
Host port:
SCSI target(s) (0, 1, 2, 3)
Preferred target(s) (0, 1)
TRANSFER_RATE_REQUESTED = 20MHZ
Host Functionality Mode = A
Allocation class 0
Command Console LUN is target 0, lun 1
Cache:
32 megabyte write cache, version 4
Cache is GOOD
Battery is GOOD
Unflushed data in cache
CACHE_FLUSH_TIMER = DEFAULT (10 seconds)
NOCACHE_UPS
Mirrored Cache:
32 megabyte write cache, version 4
Cache is GOOD
Battery is GOOD
Unflushed data in cache
Extended information:
Terminal speed 9600 baud, eight bit, no parity, 1 stop bit
Operation control: 00000004 Security state code: 90916
Configuration backup disabled
Power Supply failure cleared.
Temperature is within optimum range.
HSZ70 > show other full

Controller:
HSZ70 ZG93207803 Firmware V73Z-0, Hardware H04
Configured for dual-redundancy with ZG93207867
In dual-redundant configuration
Device Port SCSI address 6
Time: NOT SET
Host port:
SCSI target(s) (0, 1, 2, 3)
Preferred target(s) (2, 3)
TRANSFER_RATE_REQUESTED = 20MHZ
Host Functionality Mode = A
Allocation class 0
Command Console LUN is target 0, lun 1
Cache:
32 megabyte write cache, version 4
Cache is GOOD
Battery is GOOD
No unflushed data in cache
CACHE_FLUSH_TIMER = DEFAULT (10 seconds)
NOCACHE_UPS
Mirrored Cache:
32 megabyte write cache, version 4
Cache is GOOD
Battery is GOOD
No unflushed data in cache
Extended information:
Terminal speed 9600 baud, eight bit, no parity, 1 stop bit
Operation control: 00000004 Security state code: 69130
Configuration backup disabled
Power Supply failure cleared.
Temperature is within optimum range.
HSZ70 > show connection

Error 9060: Container or unit CONNECTION does not exist
Power Supply failure cleared.
Temperature is within optimum range.
HSZ70 > show failedset

Name Storageset Uses Used by
------------------------------------------------------------------------------

FAILEDSET failedset DISK50000
DISK50100
DISK60000
Switches:
NOAUTOSPARE
Power Supply failure cleared.
Temperature is within optimum range.

[Rob Leadbeater]

Hi,

It looks like you have three failed disks, but everything looks as though it should still be working, albeit in a reduced state.

What is the issue you're trying to resolve ?

Cheers,

Rob

[Pieter 't Hart]

>>> Power Supply failure cleared.
Temperature is within optimum range <<<
seems (one of the) power supply lost it's power but has been restored.

do "clear errors-cli" to clear repeating of this message.

"show connection" is probably the wrong command; try "show connections" instead.

"Time: NOT SET" in "show this_controller" output is a little awkard to determine when problems have taken place.

As Rob allready said, you've got three disks that failed.
DISK50000 disk 5 0 0 FAILEDSET
Misconfigured: No device at this PTL, please see user guide
DISK50100 disk 5 1 0 FAILEDSET
Misconfigured: No device at this PTL, please see user guide
DISK60000 disk 6 0 0 FAILEDSET
Misconfigured: No device at this PTL, please see user guide

They may have been replaced by disks that previously were in the spareset.
(R1 DISK500000 replaced by 601000 ?)

Raidset R2 has lost one disk
(REDUCED : possibly DISK50100 was member4)

Do "delete disk50100"
replace physical disk
"add disk50100 5 1 0 "
"add raidset D2 disk"
or "add spareset disk50100"
after wich it may automatically be transfered from the spareset to R2.

also replace the other two failed disks and add them to the spareset.

[mac2008_1]

yes,R1 DISK500000 replaced by 601000