- Community Home
- >
- Servers and Operating Systems
- >
- Legacy
- >
- Operating System - Tru64 Unix
- >
- robotic arm is not getting recognised on tru64 sys...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-01-2004 10:58 PM
тАО09-01-2004 10:58 PM
robotic arm is not getting recognised on tru64 system
On tru64 5.1 system, hp SDLT 320 has been connected. If scan the the devices, it recognises only the tape drive, but not the robotic arm. see the out put of
hwmgr -view devices
64: /dev/ntape/tape12 COMPAQ SDLT320 bus-2-targ-5-lun-
regs
Prathibha
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-02-2004 01:15 AM
тАО09-02-2004 01:15 AM
Re: robotic arm is not getting recognised on tru64 system
is that changer on the supported option list for your system and did you meet the os requirements for it?
greetings,
Michael
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-02-2004 04:52 PM
тАО09-02-2004 04:52 PM
Re: robotic arm is not getting recognised on tru64 system
Yes it is there in the Support matrix, and about os reqirements, is the latest one.
regs
prathibha
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-02-2004 08:51 PM
тАО09-02-2004 08:51 PM
Re: robotic arm is not getting recognised on tru64 system
Be sure your ddr.dbase is up-to-date and modified as described within these installation guides.
Use the "search" function within this forum for additional information about configuring the robot or read the instruction of your backup software.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-05-2004 06:26 PM
тАО09-05-2004 06:26 PM
Re: robotic arm is not getting recognised on tru64 system
It must be different what other devices uses ie. tape drivers and controler.
Regards
Ilkka S
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-05-2004 09:52 PM
тАО09-05-2004 09:52 PM
Re: robotic arm is not getting recognised on tru64 system
Thus, You've got an option to forget to connect it to your host :-).
2) Do You see it from SRM console?
>>> show device
3) When I had shch library, I set up the robot to load next tape automatically just upon un-load.
#mt -f /dev/ntape/tape0_d1 offline
- and robot unload this tape and loads new one automatically. And You do not need to see the robot at all.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-06-2004 05:34 PM
тАО09-06-2004 05:34 PM
Re: robotic arm is not getting recognised on tru64 system
Thanks for the mails, as this device is an autoloader there is only scsi port, there is no separate scsi bus externally, and this port has been connected to the host.
when I tried mounting the tape it give below error
Error on device named /dev/tape/tape12_d1 - Place SDLT320 tape drive unit #21 ON
LINE
regs
prathibha