- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - VMware
- >
- AF401A and VMware ESXi
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-19-2010 04:21 AM
тАО04-19-2010 04:21 AM
AF401A and VMware ESXi
I just got two HP R/T3000 UPS' and I have AF401A management modules installed in both.
Where can I find instructions about how to install an agent under vmware ESXi/ESX 4.0?
Thanks.
- Tags:
- UPS
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-19-2010 08:20 PM
тАО04-19-2010 08:20 PM
Re: AF401A and VMware ESXi
If you are running ESXi, you may need to run a management appliance vm.
Steven
HP Master ASE, Storage, Servers, and Clustering
MCSE (NT 4.0, W2K, W2K3)
VCP (ESX2, Vi3, vSphere4, vSphere5, vSphere 6.x)
RHCE
NPP3 (Nutanix Platform Professional)
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-03-2011 09:48 PM
тАО08-03-2011 09:48 PM
Re: AF401A and VMware ESXi
Hello.... I know this is an old post, but I would love to hear if there was a solution.
I have the same AF401A and the R/T3000 UPS. I am using ESXi 4.1.
Thanks
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-18-2011 08:36 AM - edited тАО08-18-2011 08:42 AM
тАО08-18-2011 08:36 AM - edited тАО08-18-2011 08:42 AM
Re: AF401A and VMware ESXi
Procedure to configure the UPS MM and connect the server to it:
1. Attach the UPS MM to the designated optional communication slot in the UPS. Using the HP provided serial cable connect the UPS MMтАЩs config/passthru port to computerтАЩs serial port. Attach the network cable to the UPS MMтАЩs 10/100 MBPS network port and network switch.
2. Using the HyperTerminal on windows system or any serial communication tool on the connected computer, assign an IP address to the UPS MM.
3. Install UPS MM Power Protection Agent (PPA) on all the connected servers (use the Linux PPA for ESX systems).
Click here to find the list of supported OS versions:
4. During the installation of the PPA, it may prompt for the connection method (serial or network), provide either the serial port name or the IP assigned to the UPS MM as prompted.
5. Using any internet browser with Java compatibility, Open the UPS MMтАЩs web-console on any connected systemтАЩs using the URL http://
6. Go to the attached devices screen, add connected servers as new devices and provide IP address of the server or proper serial port to which servers is attached to UPS MM.
7. After a few minutes, the attached device status will turn the green status indicating the successful connection between the UPS MM and Servers.
8. Then on the UPS MM's web console, go to Power-fail menu to configure the required shutdown delay time and restart delay time.
9. If needed, check by simulating input power fail on the UPS and confirm whether the connected server shutdown properly after the defined delay time.
Click here to Download the PPA:
Note: Please test the procedure on a non production ESX server
I work for HPE
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-18-2011 08:43 AM
тАО08-18-2011 08:43 AM
Re: AF401A and VMware ESXi
Note: Please test the procedure on a non production ESX server
Procedure to configure the UPS MM and connect the server to it:
1. Attach the UPS MM to the designated optional communication slot in the UPS. Using the HP provided serial cable connect the UPS MMтАЩs config/passthru port to computerтАЩs serial port. Attach the network cable to the UPS MMтАЩs 10/100 MBPS network port and network switch.
2. Using the HyperTerminal on windows system or any serial communication tool on the connected computer, assign an IP address to the UPS MM.
3. Install UPS MM Power Protection Agent (PPA) on all the connected servers (use the Linux PPA for ESX systems).
Click here to find the list of supported OS versions:
4. During the installation of the PPA, it may prompt for the connection method (serial or network), provide either the serial port name or the IP assigned to the UPS MM as prompted.
5. Using any internet browser with Java compatibility, Open the UPS MMтАЩs web-console on any connected systemтАЩs using the URL http://
6. Go to the attached devices screen, add connected servers as new devices and provide IP address of the server or proper serial port to which servers is attached to UPS MM.
7. After a few minutes, the attached device status will turn the green status indicating the successful connection between the UPS MM and Servers.
8. Then on the UPS MM's web console, go to Power-fail menu to configure the required shutdown delay time and restart delay time.
9. If needed, check by simulating input power fail on the UPS and confirm whether the connected server shutdown properly after the defined delay time.
Click here to Download the PPA:
Note: Please test the procedure on a non production ESX server
I work for HPE