- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - VMware
- >
- vSwitch and Procurve 2510G Loadbalancing Trunk
Operating System - VMware
1753479
Members
4836
Online
108794
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-30-2010 12:35 AM
тАО03-30-2010 12:35 AM
vSwitch and Procurve 2510G Loadbalancing Trunk
Hello,
I have a Proliant dl380g6 with ESX4 and want to configure a 2G loadbalincing vSwitch with a Procurve 2510G (24) Switch. Each time I tried to I got network problems (some clients could not access the ip, vm's and so on).
So my question is what configuration would be the best/functional soultion with that environment.
On HP Switch I set the trunk mode to "trunk", what I read on vmware forum.
What will be the best "balancing mode" for the vSwitch on esx- server. Tried every mode except mac based one.
Waht else has to be considered when enabling a trunk?
I have a Proliant dl380g6 with ESX4 and want to configure a 2G loadbalincing vSwitch with a Procurve 2510G (24) Switch. Each time I tried to I got network problems (some clients could not access the ip, vm's and so on).
So my question is what configuration would be the best/functional soultion with that environment.
On HP Switch I set the trunk mode to "trunk", what I read on vmware forum.
What will be the best "balancing mode" for the vSwitch on esx- server. Tried every mode except mac based one.
Waht else has to be considered when enabling a trunk?
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-08-2010 11:49 AM
тАО06-08-2010 11:49 AM
Re: vSwitch and Procurve 2510G Loadbalancing Trunk
Were you able to work this out?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-08-2010 09:58 PM
тАО06-08-2010 09:58 PM
Re: vSwitch and Procurve 2510G Loadbalancing Trunk
Set the switch trunk- mode to "trunk".
Set the vSwitch Mode to IP- HASH.
That sould work, suggested me the HP- Support.
I couldn't test that, cause had no time.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP