- Community Home
- >
- Networking
- >
- Switching and Routing
- >
- Aruba & ProVision-based
- >
- Hp 2930M - Bandwith errors
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-03-2017 05:24 AM
11-03-2017 05:24 AM
Hi all,
I've got two 2930M switches with a 10 Gbit modules at the back.
I've connected on each switch a server with two 10 Gbit interfaces. When doing an iperf speed test, I get a maximum bandwith of 5 Gbit. That should be 10 Gbit? What could be the problem causing a half bandwith?
The setup is simple. I've got 2 VLAN's, DATA & BACKUP. Each interface of the server is in one of the two vlans.
Kind regards,
Thomas
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-03-2017 09:49 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-06-2017 04:59 AM
11-06-2017 04:59 AM
Re: Hp 2930M - Bandwith errors
Just one iperf server and one iperf client. And then test.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-06-2017 03:06 PM - edited 11-06-2017 03:10 PM
11-06-2017 03:06 PM - edited 11-06-2017 03:10 PM
Re: Hp 2930M - Bandwith errors
Mate, you should explain it a little bit better...if I understood you correctly...you performed an iperf client(s)/server test doing VLAN routing (depending on where you placed the iperf server and/or clients)...you hadn't tested iperf on each VLAN staying into each VLAN's boundary (so you forced your Switch to route the traffic between VLANs during your iperf tests, is that right?).
I'm not an HPE Employee
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-07-2017 12:16 AM
11-07-2017 12:16 AM
Re: Hp 2930M - Bandwith errors
Hi,
I'm testing iPerf on IP, so it stays between the VLAN boundaries.
Hopefully you have enough info.
Kind regards,
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-07-2017 12:34 AM - edited 11-07-2017 12:35 AM
11-07-2017 12:34 AM - edited 11-07-2017 12:35 AM
Re: Hp 2930M - Bandwith errors
Hi @_Thomas_ we all generally perform iperf Client/Server's tests using IP Addresses...so that doesn't mean nothing...if your iperf Server is on VLAN A and your iperf Client is on VLAN B and if IP Routing between those VLANs is enabled (and managed by your Switch) you're testing iperf Client/Server communication doing inter-VLAN Routing (using Switch routing Hardware/Software resources)...and this can have a performance (negative) impact on data throughput you experienced.
If this is not the case further diagnostic should be carried out on both sides (Host and Switch).
I'm not an HPE Employee
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-07-2017 01:18 AM
11-07-2017 01:18 AM
Re: Hp 2930M - Bandwith errors
Hi,
The client and server are in the same VLAN. So were are using the IP addresses in the same subnet.
Kind regards,
Thomas
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-07-2017 02:02 AM - edited 11-07-2017 02:35 AM
11-07-2017 02:02 AM - edited 11-07-2017 02:35 AM
Re: Hp 2930M - Bandwith errors
@_Thomas_you forgot to attach the configuration file you already attached on the Aruba AirHeads community thread (here): looking at it you're using a Smart Rate capable - AKA IEEE 802.3bz - module (exactly the Aruba 3810M/2930M 4 1/2.5/5/10 GbE HPE Smart Rate Module with Aruba SKU JL081A)...that 5Gbps limit probably sounds less strange now.
Redacted:
Running configuration: ; JL321A Configuration Editor; Created on release #WC.16.04.0008 ; Ver #nn:nn.nn.nn.nn.nn.nn.nn.nn.nn.nn.nn.nn.nn.nn.nn.nn:nn ; encrypt-cred Nft4lYgEmtFDDOA09uxyOX0iFtQdJbGWqRCOyYV3EcHIQL4kRTCDZvOx3PKxedTE hostname "Switch01" module 1 type JL321A flexible-module A type JL081A timesync sntp sntp unicast sntp server priority 1 8.8.8.8 no telnet-server time daylight-time-rule western-europe time timezone 60 ip default-gateway 192.168.0.1 snmp-server community "public" unrestricted vlan 50 name "Backup" untagged A3 tagged A1 no ip address exit vlan 111 name "Servers" untagged A2 tagged A1 no ip address exit spanning-tree spanning-tree Trk1 priority 4 spanning-tree Trk2 priority 4 spanning-tree Trk3 priority 4 no tftp server loop-protect all loop-protect trap loop-detected loop-protect disable-timer 60
So that can be a starting point to see if there is a relationship with speed limit(s) you see.
What is the output of show interface A2-A3 smartrate command for ports you used (I suspect A2 and A3)?
I'm not an HPE Employee
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-07-2017 02:35 AM
11-07-2017 02:35 AM
Re: Hp 2930M - Bandwith errors
Hi,
Sorry, I thought I attached it. I first thought indeed that the problem was a faulty negotiation of the smart rate capabilities.
I tried to put it static on 10Gb-full duplex, but still doesn"t work.
I also get 5.92Gbit/s, not a solid 5, I would expect.
Kind regards,
Thomas Willems
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-07-2017 03:05 AM - edited 11-07-2017 03:12 AM
11-07-2017 03:05 AM - edited 11-07-2017 03:12 AM
Re: Hp 2930M - Bandwith errors
At this point also outputs of show interfaces A1-A4 and a show show interface port-utilization (limited to A1-A4 ports) commands would help...
(Not) silly question: are Host<-->Switch patch cables (are you testing directly, isn't? I mean: not through a cabling distribution system...) Cat.6 (if link is shorter than 55 meters) or Cat.6A certified for use with 10Gbps links? Have you already played with cabling (trying STP or UTP as Cat.6/6A short Patch Cables?)
I'm not an HPE Employee