- Community Home
- >
- Networking
- >
- Switching and Routing
- >
- Aruba & ProVision-based
- >
- Re: Hp Procurve 2610 inter vlan routing
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-01-2013 06:48 PM - last edited on 11-03-2013 08:07 PM by Lisa198503
11-01-2013 06:48 PM - last edited on 11-03-2013 08:07 PM by Lisa198503
Hp Procurve 2610 inter vlan routing
Can anyone help me sort out some intervlan routing issues.
Here is the stack over flow configuration exports, as well as ip route table.
http://stackoverflow.com/questions/19737924/hp-procurve-2610-intervlan-routing
Existing vlans are working, but vlan 4 which is newly created is not working.
The route automatically creates when you create a new vlan and assign it a network. So what am i doing wrong?
P.S. This thread has been moved from Comware-Based to ProCurve / ProVision-Based. -HP Forum Moderator
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-03-2013 06:05 PM
11-03-2013 06:05 PM
Re: Hp Procurve 2610 inter vlan routing
So, the new VLAN interface is created, its subnet appears as "connected" in your "show ip route", therefore it's working.
What makes you think it isn't working?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-04-2013 02:33 PM
11-04-2013 02:33 PM
Re: Hp Procurve 2610 inter vlan routing
That's actually by design... ;- )
The 2610-series is limited Layer-3. One of their limitations is that there is a maximum of six static routes.
You have three manually defined; you already have three VLAN's with an IP-adddress. Those routed VLANs probably count as one static route each, I have never tried this setup myself.
So adding your fourth routed VLAN will add a seventh static route, which is not applied. Doesn't your log (at the time you created VLAN4) give a clou ?
If you want to test this theory: remove one of the IP-adresses on the other VLANs, or remove one of the static routes. I'm not sure whether VLAN 4 should immediately start routing, but I would think so.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-06-2013 09:50 AM
11-06-2013 09:50 AM
Re: Hp Procurve 2610 inter vlan routing
I cannot ping the gateway from any vlan.
The hosts on the vlan cannot ping outside the vlan....
Host can ping its gateway of 10.10.1.1 but thats it...
So its not working.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-06-2013 09:53 AM
11-06-2013 09:53 AM
Re: Hp Procurve 2610 inter vlan routing
Yes, but my addition isnt listed as a static route.... when i show ip route its listed as a dynamic last i remembered. also looking at show ip route I have currently 4 static routes defined in my switch..