- Community Home
- >
- Networking
- >
- Switching and Routing
- >
- Aruba & ProVision-based
- >
- Re: Remote Syslogging-HP Procurve 2600
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-22-2011 03:35 PM - last edited on 11-24-2013 06:33 PM by Lisa198503
02-22-2011 03:35 PM - last edited on 11-24-2013 06:33 PM by Lisa198503
Remote Syslogging-HP Procurve 2600
I am attempting to set up remote sys logging on my HP Procurve 2600 series switches, I used the following commands to enable it but it doesn't seem to work.
logging facility syslog
logging 192.168.X.X
the firewall is off on the machine I am sending to and the listener is set to allow incoming from the switches, I am not receiving any logs on the listener, is there more to it?
Are these the right commands?
P.S. This thread has been moved from Switches, Hubs, Modems (Legacy ITRC forum) to ProCurve / ProVision-Based. -HP Forum Moderator
- Tags:
- syslog
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-23-2011 02:29 AM
02-23-2011 02:29 AM
Re: Remote Syslogging-HP Procurve 2600
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-23-2011 03:37 PM
02-23-2011 03:37 PM
Re: Remote Syslogging-HP Procurve 2600
snmp-server contact "Steve Branin"
snmp-server location "Coralville Mez"
mirror-port 37
qos dscp-map 101110 priority 6
interface 44
name "CMAU"
exit
ip default-gateway 192.168.1.4
ip routing
logging facility syslog
logging 192.168.1.143
snmp-server community "public" Unrestricted
vlan 1
name "DEFAULT_VLAN"
untagged 1-52
ip address 192.168.1.80 255.255.255.0
ip igmp
exit
vlan 20
name "voice"
ip address 192.168.2.1 255.255.255.0
tagged 1-50
voice
ip igmp
exit
fault-finder bad-driver sensitivity high
fault-finder bad-transceiver sensitivity high
fault-finder bad-cable sensitivity high
fault-finder too-long-cable sensitivity high
fault-finder over-bandwidth sensitivity high
fault-finder broadcast-storm sensitivity high
fault-finder loss-of-link sensitivity high
fault-finder duplex-mismatch-HDx sensitivity high
fault-finder duplex-mismatch-FDx sensitivity high
stack commander "CORA"
stack member 1 mac-address 001f289ecd80
stack member 2 mac-address 001f289f4480
stack member 3 mac-address 001f289f6100
stack member 4 mac-address 001f28833dc0
password manager
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-24-2011 02:31 AM
02-24-2011 02:31 AM
Re: Remote Syslogging-HP Procurve 2600
command enough
which system log server using
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-24-2011 02:04 PM
02-24-2011 02:04 PM
Re: Remote Syslogging-HP Procurve 2600
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-25-2011 05:57 AM
02-25-2011 05:57 AM
Re: Remote Syslogging-HP Procurve 2600
teraterm pro
whit use logging 192.168.X.X
command
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-20-2013 06:16 PM
11-20-2013 06:16 PM
Re: Remote Syslogging-HP Procurve 2600
very simple;
in switch add :
logging facility syslog
logging 172.16.1.50 (this is my syslogd server)
in this case i used FreeBSD-9.2 as syslogd server
in /etc/syslog.conf, please add:
+172.16.1.31
*.* /var/log/switch-31.log (let's said this is first switch)
+172.16.1.32
*.* /var/log/switch-32.log (let's said this is second switch)
+172.16.1.33
*.* /var/log/switch-33.log (let's said this is third switch)
Then, don't forget create the log files by touching them all by:
touch /var/log/switch-31.log (repeat this touching for the other switch that you have)
in /etc/rc.conf, please add (this is efective for run syslogd every boot start) :
syslogd_enable="YES"
syslogd_flags=""
restart the daemon of syslogd (in FreeBSD) /etc/rc.d/syslogd restart
suggestion: sometime all of them could be effective by reboot the server
Please, make sure that syslogd running properly, check the service by : ps ax | grep syslogd
simple Testing:
in syslogd server do : tail -f /var/log/switch-31.log
in switch, if you have enabled the ssh remote, do the remote the switch using ssh, but please use the wrong password (it should repeat for three times), and check the result of "tail" above, you should see the log about wrong password login.
ok bro, i hope you can do these successfully...see ya!
(# weh island - Indonesia #)