- Community Home
- >
- Networking
- >
- Switching and Routing
- >
- Aruba & ProVision-based
- >
- Re: VLAN IP Addressing / DHCP Relay
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-07-2014 07:45 AM - edited 10-07-2014 08:03 AM
10-07-2014 07:45 AM - edited 10-07-2014 08:03 AM
VLAN IP Addressing / DHCP Relay
Hi
i have a Pro Curve 2810-48G swtich and i am trying to separate mobile phone wifi traffic and laptop wifi traffic.
the way i plan to do this is via an access point which supports multiple SSIDs and assign VLans to the SSIDs
i will have
SSID 1 - VLAN1 (Default) - for wireless laptops and desktops
SSID2 - VLAN2 (WIFI) - for wireless mobiles phones / tablets / BYOD
on the switch i have tagged ports 22 and 24 for both V LAN 1 and 2 as these are ports that the Access points will patch into? - is this correct or should the ports only be tagged into VLAN 2
as the access point will have both mobile devices ( VLAN2) and laptops (VLAN1) i have tagged the ports under both VLANS
the next question is do i need to assign an IP address to VLAN 2. the VLAN1 ip address is the current swtich address before VLANS were configured.
and finally how do i go about DHCP for v lan 2?
currently DHCP server has 10.0.0.0/24 scope which is on VLAN1
i would create another scope 10.0.1.0/24 which would be assigned to to any device connecting on VLAN2 but how do i configure this on the switch. i have tried the IP Helper address but i do not think the swtich supports it as its a layer 2 switch?
DHCP is a Windows 2003 server
any help would be greatful..
current running config below..
------------------------------------------------------------
ProCurve Switch 2810-48G# show run
Running configuration:
; J9022A Configuration Editor; Created on release #N.11.25
hostname "ProCurve Switch 2810-48G"
vlan 1
name "DEFAULT_VLAN"
untagged 1-21,23,25-48
ip address 10.0.0.9 255.255.255.0
tagged 22,24
exit
vlan 2
name "Wifi"
tagged 22,24
exit
----------------------------------------------------------------------------------------
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-09-2014 07:35 PM
10-09-2014 07:35 PM
Re: VLAN IP Addressing / DHCP Relay
Yes, you tag both VLANs on the switchports linking to the APs, and on the APs you tag both VLANs on the interfaces going to the switchports.
Yes you need an address on the switch VLAN2 interface.
Yes you need an IP helper on the VLAN2 interface.