- Community Home
- >
- Networking
- >
- Switching and Routing
- >
- Aruba & ProVision-based
- >
- Re: Vlan routing on HP 5412zl
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-02-2013 05:06 PM
тАО01-02-2013 05:06 PM
Hi there,
I have been working to reconfigure my network with Vlans. The current network has every device on the same subnet of 192.168.0.0 / 21.
I have been working on separating traffic out onto Vlans based on devices and everything is going great until the new Vlans try to access to the gatway.
Each vlan's gateway is my core 5412 switch and then I have a static route set as
ip route 0.0.0.0 0.0.0.0 192.168.0.5
192.168.0.5 is currently the address of the firewall, which acts as the Internet gateawy. Now the old network can access this just fine but any of the new Vlans cannot get to this address.
Any insight would be great below I have posted some of the config of the switch
-------------------------
Running configuration:
; J8698A Configuration Editor; Created on release #K.15.08.0008
; Ver #02:1b.ef:f6
hostname "ITRoom5412zl"
module 1 type j8705a
module 2 type j8705a
module 6 type j8702a
module 8 type j9154a
module 9 type j8702a
module 11 type j8702a
module 12 type j8702a
power-over-ethernet pre-std-detect
ip route 0.0.0.0 0.0.0.0 192.168.0.5
ip routing
snmp-server community "public" unrestricted
vlan 1
name "DEFAULT_VLAN"
no untagged A13-A19,B14,F1-F3,F5,F7,F12,H1-H2,I1,I15-I24
untagged A1-A12,A20-A24,B1-B13,B15-B24,F4,F6,F8-F11,F13-F24,I2-I14,K1-K24,L1-L24
ip address 192.168.0.27 255.255.248.0
exit
vlan 3
name "DEPLOYMENT"
tagged B24
ip address 172.16.3.254 255.255.255.0
exit
vlan 16
name "DEVICES"
untagged H2,I1,I15-I24
tagged B24
ip address 172.16.16.254 255.255.255.0
ip helper-address 172.16.17.10
exit
vlan 17
name "SERVERS"
untagged F7,F12,H1
tagged B24
ip address 172.16.17.254 255.255.255.0
exit
------------------------
show ip route
IP Route Entries
Destination Gateway VLAN Type Sub-Type Metric Dist.
------------------ --------------- ---- --------- ---------- ---------- -----
0.0.0.0/0 192.168.0.5 1 static 1 1
127.0.0.0/8 reject static 0 0
127.0.0.1/32 lo0 connected 1 0
172.16.3.0/24 DEPLOYMENT 3 connected 1 0
172.16.16.0/24 DEVICES 16 connected 1 0
172.16.17.0/24 SERVERS 17 connected 1 0
192.168.0.0/21 DEFAULT_VLAN 1 connected 1 0
Any help would be great
Solved! Go to Solution.
- Tags:
- VLAN
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-02-2013 10:33 PM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-03-2013 03:57 PM
тАО01-03-2013 03:57 PM
Re: Vlan routing on HP 5412zl
Hi Alex,
I have added routes to my firewall as seen here. I have only added the one for VLAN 17 at the moment
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
172.16.17.254 * 255.255.255.255 UH 0 0 0 lan-1
172.16.17.0 172.16.17.254 255.255.255.0 UG 0 0 0 lan-1
10.129.96.0 * 255.255.248.0 U 0 0 0 wan-1
192.168.0.0 * 255.255.248.0 U 0 0 0 lan-1
default 10.129.96.18 0.0.0.0 UG 0 0 0 wan-1
Interface lan-1 is the inside and wan-1 is the outside.
Is there something else that I have to add to the switch config for this to work? The firewall is currently on Default Vlan 1 and is the rest of the 192.168.x.x network.
The switch can ping 192.168.0.5 (Firewall address)
The firewall can ping 192.168.0.27 (Switch VLAN 1 address)
The firewall cannot ping 172.16.17.254 (Switch VLAN 17 address)
Any suggestions would be greatly appreciated.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-03-2013 10:36 PM
тАО01-03-2013 10:36 PM
Re: Vlan routing on HP 5412zl
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-03-2013 11:23 PM
тАО01-03-2013 11:23 PM
Re: Vlan routing on HP 5412zl
Paul
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-21-2013 04:20 PM
тАО02-21-2013 04:20 PM
Re: Vlan routing on HP 5412zl
HI there,
The problem was the Firewall. Needed to create routes back to the switch for the other networks.
Just for completeness if anyone is curious, I have an IPCop firewall, I had to SSH into it and run the following command for each VLAN or network:
route add -net 172.16.3.0 netmask 255.255.255.0 gw 192.168.0.27
Where 172.16.3.0 was the network needed to connect and 192.168.0.27 is the IP of the routing HP Switch.
Also IPCop does not remember these beyond reboots so it has to be added to the rc.d scripts that run on startup. IPCop has some documentation on how to do this on their site for the different version.
Thanks for the suggestions everyone
Tyson
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-21-2013 07:40 PM
тАО02-21-2013 07:40 PM
Re: Vlan routing on HP 5412zl
Paul
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-29-2017 08:20 AM
тАО12-29-2017 08:20 AM
Re: Vlan routing on HP 5412zl
I need your help, I have the same problem. https://community.spiceworks.com/topic/2100617-intervlan-is-not-working-please-i-need-help?page=1#entry-7462410
This is my post please I need your help, have you solved your problem....my problem that my active directory is in a separate vlan and it is not recognized by a host in a separate vlan. I want to do inter vlan communication through the 5412 core switch...
Thanks