- Community Home
- >
- Servers and Operating Systems
- >
- Legacy
- >
- ProLiant Deployment and Provisioning
- >
- Re: RDeploy hangs during image creation
ProLiant Deployment and Provisioning
1753477
Members
4693
Online
108794
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
12-14-2004 11:26 PM
12-14-2004 11:26 PM
RDeploy hangs during image creation
We have been using RDP to create and deploy images on our HP BL20P blades for several months now, without incident. Recently these processes become hit and miss and now they seem to stop working altogether.
We setup an image creation job and send it to the desired blade. The blade powers down, goes into PXE mode, obtains an DHCP IP Address but then hangs at "Initializing TCPIP over DHCP" and will not continue.
We have tried resetting our DHCP Server, Reseating the blade, and re-installed the altiris client. RDP was installed over a prior install of Altiris deployment server and our RDP console version is 6.1, SP1.
Any thoughts would be greating appreciated.
We setup an image creation job and send it to the desired blade. The blade powers down, goes into PXE mode, obtains an DHCP IP Address but then hangs at "Initializing TCPIP over DHCP" and will not continue.
We have tried resetting our DHCP Server, Reseating the blade, and re-installed the altiris client. RDP was installed over a prior install of Altiris deployment server and our RDP console version is 6.1, SP1.
Any thoughts would be greating appreciated.
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
12-15-2004 03:03 AM
12-15-2004 03:03 AM
Re: RDeploy hangs during image creation
Note what IP the blade gets as soon as the PXE boot prcoess starts - it says "CLIENT IP=x.x.x.x". Shut the blade down and ping that address. Most likely you have something configured to use that address and it was not reserved in DHCP. Set a reservation in DHCP for that address and reserve it to aabbccddeeff and no one will ever get it. Do this even if nothing replies to your ping (this happens if the device doesn't respond to ICMP).
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP