- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- Re: 1777 post error on dl360 G1
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-04-2005 10:59 PM
тАО07-04-2005 10:59 PM
1777 post error on dl360 G1
DL360 G1, with Smart Array Controller (ver 1.50) and the following error:
1777-Slot 0 Drive Array - Proliant Storage Enclosure Problem detected
SCSI Port 2: Interrupt Signal Inoperative - Check SCSI Cables
This error comes out only when the frontal scsi cage is mounted.
I've tried three different scsi cages, all with the same result.
What else to do?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-04-2005 11:37 PM
тАО07-04-2005 11:37 PM
Re: 1777 post error on dl360 G1
try to clear the NVRAM
then check again.
any error led on the board check image attached
Check with cable and and no hdd attached on the server any error mesasage on screen
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-05-2005 02:16 AM
тАО07-05-2005 02:16 AM
Re: 1777 post error on dl360 G1
thanks for answering.
Motherboard is 173837-001, cpu 2x 933Mhz
Firmware P21 11/15/2002
After clearing and recycling power, LED are these:
LED 1 Green
LED 2 Off
LED 2A Off
LED 3 Off
LED 3A Green
LED 4 Off
Thanks,
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-12-2005 06:31 AM
тАО07-12-2005 06:31 AM
Re: 1777 post error on dl360 G1
-Brian
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-12-2005 06:14 PM
тАО07-12-2005 06:14 PM
Re: 1777 post error on dl360 G1
I've solved it my way.
As the system is working very well, despite the alert, I've set DL360 to not STOP (F1 prompt) in case of error.
I'ld prefer to see no error, but lacking any information on how to do that, simply avoiding F1 solves my situation.
Ciao,
Tonino