- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- Re: Adding RAID 5
ProLiant Servers (ML,DL,SL)
1753734
Members
4717
Online
108799
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
12-18-2003 10:32 AM
12-18-2003 10:32 AM
Adding RAID 5
This may be a stupid question, forgive my ignorance, but can you "turn on" RAID 5 after the fact?
I have a Proliant 1600 w/Smart-2SL controller running Netware 5. Currently 2 9.1gb drives with no RAID features at all. One is SYS vol and other is VOL1 vol. I would like to add 3 more 9.1gb drives and "turn on" RAID 5.
I fear this is NOT possible, in which case I assume I must backup both vols to tape, setup RAID 5 on the drives, (which will probably wipe them), install a base Netware enough to load tape drivers and restore system. Is this right?
I have a Proliant 1600 w/Smart-2SL controller running Netware 5. Currently 2 9.1gb drives with no RAID features at all. One is SYS vol and other is VOL1 vol. I would like to add 3 more 9.1gb drives and "turn on" RAID 5.
I fear this is NOT possible, in which case I assume I must backup both vols to tape, setup RAID 5 on the drives, (which will probably wipe them), install a base Netware enough to load tape drivers and restore system. Is this right?
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
12-18-2003 02:40 PM
12-18-2003 02:40 PM
Re: Adding RAID 5
Hi Robert,
You are right when saying that you have to backup and then reinstall and restore from tape if you want all your drives to be in a raid5 configuration, unless you only want to use raid 5 for 3 new drives.
Hope this help
Thierry
You are right when saying that you have to backup and then reinstall and restore from tape if you want all your drives to be in a raid5 configuration, unless you only want to use raid 5 for 3 new drives.
Hope this help
Thierry
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP