- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- Adding a DLT Drive
ProLiant Servers (ML,DL,SL)
1753873
Members
7572
Online
108809
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-06-2001 04:00 PM
03-06-2001 04:00 PM
Adding a DLT Drive
DOES ANYONE HAVE THE EXACT ANSWERS TO THE QUESTIONS ASKED UNDER THE MKDEV TAPE COMMAND WHEN ADDING A DLT DEVICE TO THROUGH SCOUNIX FOR TEH COMPAQ PROLIANT 5000?
We are currently running Sco Open Server 5 (Sco_SV 3.2v5.0.2)
on a Compaq 5000 Proliant Server. At the end of the email, I have a few questions for any firms on ScoUnix that have successfully installed a DLT tape device.
In attempting to install a DLT tape device to backup Informix, the Compaq server recognizes the SCSI device, but we cannot TAR a file to the DLT through ScoUnix. We configured the device through the command "mkdev tape". Our DAT devices were configured as "General SCSI Devices" and the host adaptor driver "cha". We chose the same options for the DLT device (the general SCSI is the only option that made sense from those listed) and "cha" as the host adaptor driver.
Compaq support recommends that we upgrade our EFS, choose "clad" as the host adaptor driver, and then relink the kernel after configuring the DLT.
If you have a DLT tape device on your system, please answer the following where applicable:
ScoUnix version?
Server?
If Compaq, EFS version (command at prompt = "cpqefsver")
Host Adaptor Driver? (in the "mscsi" file under directory /etc/conf/cf.d/ )
We also tried to remove the improperly configured device through ScoAdmin, but it did not allow us to do so and also didn't communicate any errors. Any suggestions would be greatly appreciated.
We are currently running Sco Open Server 5 (Sco_SV 3.2v5.0.2)
on a Compaq 5000 Proliant Server. At the end of the email, I have a few questions for any firms on ScoUnix that have successfully installed a DLT tape device.
In attempting to install a DLT tape device to backup Informix, the Compaq server recognizes the SCSI device, but we cannot TAR a file to the DLT through ScoUnix. We configured the device through the command "mkdev tape". Our DAT devices were configured as "General SCSI Devices" and the host adaptor driver "cha". We chose the same options for the DLT device (the general SCSI is the only option that made sense from those listed) and "cha" as the host adaptor driver.
Compaq support recommends that we upgrade our EFS, choose "clad" as the host adaptor driver, and then relink the kernel after configuring the DLT.
If you have a DLT tape device on your system, please answer the following where applicable:
ScoUnix version?
Server?
If Compaq, EFS version (command at prompt = "cpqefsver")
Host Adaptor Driver? (in the "mscsi" file under directory /etc/conf/cf.d/ )
We also tried to remove the improperly configured device through ScoAdmin, but it did not allow us to do so and also didn't communicate any errors. Any suggestions would be greatly appreciated.
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-26-2002 04:00 PM
08-26-2002 04:00 PM
Re: Adding a DLT Drive
The driver used by your scsi controller is cha. I would probably talk to technical support for guidance installing this dlt drive, we will be able to configure this device since we can do it live with you on the line.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP