- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- After installing a second CPU, NT still recognizes...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-20-2001 04:00 PM
тАО02-20-2001 04:00 PM
After installing a second CPU, NT still recognizes only one CPU processor. Why? How it's work?
THANK YOU.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-25-2001 04:00 PM
тАО02-25-2001 04:00 PM
Re: After installing a second CPU, NT still recognizes only one CPU processor. Why? How it's work?
Then configure the server hardware to the correct the "APIC Mode" settings. You must start System Configuration and press 'CTRL a' at the first menu after selecting F10 during boot. This activates "Advanced Mode". Then enter System Configuration itself and follow the prompts to complete a basic configuration load. Select to "Review" the settings and then pick "View/Edit Details" from the menu. Look down the list to find "APIC Mode". Press enter on this selection and select "Full Table, Mapped" (or "Full Table" if only choice, depends on specific system). Once this has been done, exit and save changes.
The next step is to load the Multiprocessor HAL on NT. This is best accomplished with the latest Compaq NT SSD (for 3.51 or 4.0 specifically) as this utility will do a more reliable job of identifying the correct HAL for the system. Simply run SETUP.EXE from the SSD disk 1 and select the HAL upgrade (you may also install other drivers if desired, do NOT force all drivers to load as some may not work on your system).
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-04-2001 04:00 PM
тАО03-04-2001 04:00 PM
Re: After installing a second CPU, NT still recognizes only one CPU processor. Why? How it's work?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-05-2001 04:00 PM
тАО03-05-2001 04:00 PM
Re: After installing a second CPU, NT still recognizes only one CPU processor. Why? How it's work?
The reason I ask is that I understand NT SP4 can create a problem with the Compaq HAL and I have just had major problems with Exchange SP4, and had to resort to restore from tape etc.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-12-2001 04:00 PM
тАО03-12-2001 04:00 PM
Re: After installing a second CPU, NT still recognizes only one CPU processor. Why? How it's work?
The SSD is here:
NT 4.0 SSD