- Community Home
- >
- Servers and Operating Systems
- >
- ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- B110i - Array not rebuilding - Code 776 (Ready for...
-
- Forums
-
- Advancing Life & Work
- Advantage EX
- Alliances
- Around the Storage Block
- HPE Ezmeral: Uncut
- OEM Solutions
- Servers & Systems: The Right Compute
- Tech Insights
- The Cloud Experience Everywhere
- HPE Blog, Austria, Germany & Switzerland
- Blog HPE, France
- HPE Blog, Italy
- HPE Blog, Japan
- HPE Blog, Middle East
- HPE Blog, Russia
- HPE Blog, Saudi Arabia
- HPE Blog, South Africa
- HPE Blog, UK & Ireland
-
Blogs
- Advancing Life & Work
- Advantage EX
- Alliances
- Around the Storage Block
- HPE Blog, Latin America
- HPE Blog, Middle East
- HPE Blog, Saudi Arabia
- HPE Blog, South Africa
- HPE Blog, UK & Ireland
- HPE Ezmeral: Uncut
- OEM Solutions
- Servers & Systems: The Right Compute
- Tech Insights
- The Cloud Experience Everywhere
-
Information
- Community
- Welcome
- Getting Started
- FAQ
- Ranking Overview
- Rules of Participation
- Tips and Tricks
- Resources
- Announcements
- Email us
- Feedback
- Information Libraries
- Integrated Systems
- Networking
- Servers
- Storage
- Other HPE Sites
- Support Center
- Aruba Airheads Community
- Enterprise.nxt
- HPE Dev Community
- Cloud28+ Community
- Marketplace
-
Forums
-
Blogs
-
Information
-
English
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
07-14-2016 08:14 AM - edited 07-14-2016 08:20 AM
07-14-2016 08:14 AM - edited 07-14-2016 08:20 AM
B110i - Array not rebuilding - Code 776 (Ready for Recovery) is queued for rebuilding.
hello
'ive replaced 1 Hdd in Raid 1 with controller B110i but the utility (from windows) is blocked on "Code 776 (Ready for Recovery) is queued for rebuilding."
The original (last) disk is a : ATA ST500DM002-1BD14
I've put, as second disk a Seagate MB0500EBZQA
In B110i log i see some error:
Drive Model ATA ST500DM002-1BD14
Drive Serial Number Z6EGQXK3
Drive Firmware Revision KC48
SCSI Inquiry Bits 0x00
Compaq Drive Stamped Stamped For Monitoring (0x01)
Last Failure Reason Mark Bad Failed (0x05)
What's "Mark Bad Failed (0x05)" ??
Thank You to All
LOG HERE >>> ADUReport.txt
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
07-14-2016 08:31 AM
07-14-2016 08:31 AM
Re: B110i - Array not rebuilding - Code 776 (Ready for Recovery) is queued for rebuilding.
Did you reboot the server?
This controller cannot detect hot swap without a license, IIRC.
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
07-14-2016 08:34 AM
07-14-2016 08:34 AM
Re: B110i - Array not rebuilding - Code 776 (Ready for Recovery) is queued for rebuilding.
Yess, Rebooted more time.
In other forum speak about this controller : they say that accept only HP "branded" disk.
I not understand that "Mark Bad Failed (0x05)"
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
07-14-2016 10:48 AM - edited 07-14-2016 11:08 AM
07-14-2016 10:48 AM - edited 07-14-2016 11:08 AM
Re: B110i - Array not rebuilding - Code 776 (Ready for Recovery) is queued for rebuilding.
Do you see a message prompting for press F1 or F2 during boot?
from user guide:
If you are replacing a drive in a fault-tolerant configuration while the system is powered down, a POST
message appears when the system is powered up. When this message appears, press the F1 key to
enable automatic data recovery. If you do not enable automatic data recovery, the logical volume
remains in a ready-to-recover condition, and the same POST message appears when the system is
restarted.
This would look like this:
HP Smart Array B110i SATA RAID Controller (v1.10) 2 Logical Drives
786-Slot 0 Drive Array Recovery Needed
The following disk drive(s) need Automatic Data Recovery (Rebuild):
Port 1I: Box 1: Bay 1
Select "F1" to continue with recovery of data to drive(s)
Select "F2" to continue without recovery of data to drive(s)
(RESUME = "F1" OR "F2" KEY)
press F1 now!
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!

Hewlett Packard Enterprise International
- Communities
- HPE Blogs and Forum
© Copyright 2021 Hewlett Packard Enterprise Development LP