- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- BL 20pG3 Server Boot Issue
ProLiant Servers (ML,DL,SL)
1752288
Members
4625
Online
108786
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-19-2005 05:40 PM
тАО04-19-2005 05:40 PM
BL 20pG3 Server Boot Issue
We are in the process of installing 13 BL20P G3 blade servers. One server is not booting up and following is in the iLO.
Server Status: Stand-by (Amber colour light)
In virtual power buttons, only Momentary, Press and Hold and Manual Override for BL P Class are activated. We could not boot up the server with any of them.
We replace the power module, access panel and chassis. But couldnтАЩt see a difference. We plugged to other slots of the enclosure and same error occurred. We plugged other blades to same slot and they also worked fine. Server is to be connected to SAN and having Fiber connections also.
In iLO remote console shows тАЬNo power for the MonitorтАЭ. In IML it says that there is no adequate power for server to power up.
Blade arrangement is as follows:
Enclosure 1: Occupied Bays are 1-7 (Bay 6 is not working)
Enclosure 2: Occupied bays are 1-6
Both Enclosures are cascaded.
One Single Phase Power enclosure is used with 4 Power Supplies.
Server Status: Stand-by (Amber colour light)
In virtual power buttons, only Momentary, Press and Hold and Manual Override for BL P Class are activated. We could not boot up the server with any of them.
We replace the power module, access panel and chassis. But couldnтАЩt see a difference. We plugged to other slots of the enclosure and same error occurred. We plugged other blades to same slot and they also worked fine. Server is to be connected to SAN and having Fiber connections also.
In iLO remote console shows тАЬNo power for the MonitorтАЭ. In IML it says that there is no adequate power for server to power up.
Blade arrangement is as follows:
Enclosure 1: Occupied Bays are 1-7 (Bay 6 is not working)
Enclosure 2: Occupied bays are 1-6
Both Enclosures are cascaded.
One Single Phase Power enclosure is used with 4 Power Supplies.
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-08-2006 09:07 AM
тАО01-08-2006 09:07 AM
Re: BL 20pG3 Server Boot Issue
Please change the mother board .
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-08-2006 03:54 PM
тАО01-08-2006 03:54 PM
Re: BL 20pG3 Server Boot Issue
Prior you accept system board replacement try:
no adequate power ...
Verify if you get enough W from Power enclosure
With fully configured servers with Fiber cards two hard drives dual CPU ├в you might experience insufficient power after 12th or 13th server
Two main steps:
Use Service Port fro Power enclosure to Verify Redundancy
Use user Guide how to do so (hyper Terminal)
Page 841
http://h20000.www2.hp.com/bc/docs/support/SupportManual/c00065042/c00065042.pdf
Power available ????
Power consumed ????
One Phase Power Enclosure with 4 power supply provide somewhere around 4200 W
Update all management modules Firmware to 2.30
http://h18023.www1.hp.com/support/files/server/us/download/24088.html
http://h18023.www1.hp.com/support/files/server/us/locOsCat/69_65.html
Additional steps
Swap Fiber Mezzanine Card or 6i controller
Make sure memory not mixed dual or single rank or dual first
DC filer or DC/DC converter can be swapped
no adequate power ...
Verify if you get enough W from Power enclosure
With fully configured servers with Fiber cards two hard drives dual CPU ├в you might experience insufficient power after 12th or 13th server
Two main steps:
Use Service Port fro Power enclosure to Verify Redundancy
Use user Guide how to do so (hyper Terminal)
Page 841
http://h20000.www2.hp.com/bc/docs/support/SupportManual/c00065042/c00065042.pdf
Power available ????
Power consumed ????
One Phase Power Enclosure with 4 power supply provide somewhere around 4200 W
Update all management modules Firmware to 2.30
http://h18023.www1.hp.com/support/files/server/us/download/24088.html
http://h18023.www1.hp.com/support/files/server/us/locOsCat/69_65.html
Additional steps
Swap Fiber Mezzanine Card or 6i controller
Make sure memory not mixed dual or single rank or dual first
DC filer or DC/DC converter can be swapped
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP