- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- Compaq Proliant ML350 G3...power problem???
ProLiant Servers (ML,DL,SL)
1752801
Members
5729
Online
108789
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-08-2008 05:37 AM
тАО05-08-2008 05:37 AM
Compaq Proliant ML350 G3...power problem???
The server is ~3 years old. HP sent out a tech and he replaced the system board, backplane power module, and power pack. Server stayed up for 4 days and then crashed as if power plug was pulled. Next tech came out, replaced same parts, plus NIC, SCSI card, and all 4 memory cards. He also removed the tape drive and disconnected the CD and floppy to rule them out. The server ran for 4 hours. Nothing in the event viewer showed problems with hardware. I'm guessing it's either one or both fans or the power switch in front.
ANY IDEAS??? I need help ASAP. Thanks.
ANY IDEAS??? I need help ASAP. Thanks.
3 REPLIES 3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-08-2008 07:40 AM
тАО05-08-2008 07:40 AM
Re: Compaq Proliant ML350 G3...power problem???
Are you seeing anything in the system management home page? Look in the Integrated Management Log, there should be errors there.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-08-2008 07:57 AM
тАО05-08-2008 07:57 AM
Re: Compaq Proliant ML350 G3...power problem???
hi
run server in minimum configuration,
remove PCIs, just one memory at a time, just 1 proc in case you have 2
also server has al up to date drivers/firmware?
regards
run server in minimum configuration,
remove PCIs, just one memory at a time, just 1 proc in case you have 2
also server has al up to date drivers/firmware?
regards
Didn't your momma teach you to say thanks!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-09-2008 05:13 AM
тАО05-09-2008 05:13 AM
Re: Compaq Proliant ML350 G3...power problem???
The power switch and 2 fans were replaced, but not before they caused problems with the system board...which was replaced again. I now have an almost new system. Thanks for the input!!
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP