- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- Re: Compaq Proliant does not see SCSI harddrive by...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-19-2004 11:27 PM
тАО07-19-2004 11:27 PM
Compaq Proliant does not see SCSI harddrive by start up
1785-Slot 1 drive aray not configured rev A v4.16
Within the server are 3 SCSI 9.1 Gb drives installed. THe server is transported from location A to B with normal shutdown.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-19-2004 11:46 PM
тАО07-19-2004 11:46 PM
Re: Compaq Proliant does not see SCSI harddrive by start up
How old is the server? Was the server down for a while? If so, it could be that the configuration of your RAID controller has been lost due to battery failure.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-19-2004 11:48 PM
тАО07-19-2004 11:48 PM
Re: Compaq Proliant does not see SCSI harddrive by start up
Joost
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-20-2004 12:00 AM
тАО07-20-2004 12:00 AM
Re: Compaq Proliant does not see SCSI harddrive by start up
Joost
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-20-2004 12:19 AM
тАО07-20-2004 12:19 AM
Re: Compaq Proliant does not see SCSI harddrive by start up
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-21-2004 02:35 AM
тАО07-21-2004 02:35 AM
Re: Compaq Proliant does not see SCSI harddrive by start up
Could be your controller failed or the cable is faulty. It would only display that message when it doesn't see ANY of the drives in the array since the array configuration is stored on the drives themselves. Even if it sees only one drive, it should still be aware of the array configuration.
Regards,
Sigurbjartur