- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- Re: Conrep not working on DL380 G3
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-09-2003 03:05 AM
тАО05-09-2003 03:05 AM
Conrep not working on DL380 G3
If conrep is no longer supported what is it's replacement for replicating configs and setting boot order etc.?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-12-2003 12:05 AM
тАО05-12-2003 12:05 AM
Re: Conrep not working on DL380 G3
I tested this on a DL380G3 with ssst 1.9 and 2.1 version of conrep and didn't find any problems at all.
Are you sure you are using a real DOS version and not a windows DOS bootable disk?
I attached the 2.1a version configuration.
Best regards, Jeroen
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-12-2003 04:57 AM
тАО05-12-2003 04:57 AM
Re: Conrep not working on DL380 G3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-12-2003 05:38 AM
тАО05-12-2003 05:38 AM
Re: Conrep not working on DL380 G3
If I step through my autoexec.bat I can get conrep to work until pci.exe is loaded then it refuses to work.
That's a bit of a problem for me but I'll have to work round it.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-30-2003 12:42 AM
тАО09-30-2003 12:42 AM
Re: Conrep not working on DL380 G3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-30-2003 12:48 AM
тАО09-30-2003 12:48 AM
Re: Conrep not working on DL380 G3
Every time the PCI/AGP sniffer ran it stopped conrep running. Within my scripting I had to run the sniffer and redirect the output to a file, reboot the server, read the sniffer output from the file, then run conrep.
I simply couldn't get conrep to run after the sniffer.
Hope this helps
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-30-2003 08:54 AM
тАО09-30-2003 08:54 AM
Re: Conrep not working on DL380 G3
After additional testing, I realized that I was using an older version of the utility that we wrote to scan the PCI bus. The newer version plays nice with ConRep. I'm not sure what the differences between versions are--I wasn't part of the team that wrote it--but it appears that ConRep will work fine with our newer version.