- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- Re: DL320 G4 only powersupply fans start up
ProLiant Servers (ML,DL,SL)
1753889
Members
7635
Online
108809
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-10-2009 09:03 AM
тАО09-10-2009 09:03 AM
DL320 G4 only powersupply fans start up
I have a DL320 G4 which has been running fine.
Recently we found it in a down state... no leds lit or hard drives running.
Power off and back on... powersupply fans run up and nothing else.
Fault LEDs on system board have ch13 and ch14 blinking, all others are not lit..
Where can I find what this means?
Recently we found it in a down state... no leds lit or hard drives running.
Power off and back on... powersupply fans run up and nothing else.
Fault LEDs on system board have ch13 and ch14 blinking, all others are not lit..
Where can I find what this means?
3 REPLIES 3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-10-2009 09:20 AM
тАО09-10-2009 09:20 AM
Re: DL320 G4 only powersupply fans start up
The maintenance and service guide has the system board LEDs on page 59. There is no mention of Ch13 and Ch14 or any blinking but you might be able to find something else.
http://bizsupport2.austin.hp.com/bc/docs/support/SupportManual/c00576048/c00576048.pdf
http://bizsupport2.austin.hp.com/bc/docs/support/SupportManual/c00576048/c00576048.pdf
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-11-2009 04:11 AM
тАО09-11-2009 04:11 AM
Re: DL320 G4 only powersupply fans start up
If it's not listed there sometimes they co-relate to what they are next to..
And sometimes there is a description of the leds on the inside of the plate that you take out to get access to the inside of the server :p
And sometimes there is a description of the leds on the inside of the plate that you take out to get access to the inside of the server :p
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-11-2009 05:07 AM
тАО09-11-2009 05:07 AM
Re: DL320 G4 only powersupply fans start up
There is a row of LEDs next to the 2 sets of system switches with 8 LEDs. At the outer edge of the 1st LED is labled LOW.
The LEDs are labled (from outside to IN)
CR2 CR4 CR7 CR10 CR11 CR12 CR13 CR14
When the power cable is pluged in, these LED's go through some initiation process and then off, except for CR13 and CR14 (stay blinking)
If I disconnect a fan, the red alarm illuminates on the motherboard. When power switch is push, fans on PS startup, but nothing esle... no lights or fan startup or video or anything.
The LEDs are labled (from outside to IN)
CR2 CR4 CR7 CR10 CR11 CR12 CR13 CR14
When the power cable is pluged in, these LED's go through some initiation process and then off, except for CR13 and CR14 (stay blinking)
If I disconnect a fan, the red alarm illuminates on the motherboard. When power switch is push, fans on PS startup, but nothing esle... no lights or fan startup or video or anything.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP