- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- DL360 G3 Power Supply issue
ProLiant Servers (ML,DL,SL)
1750505
Members
4816
Online
108777
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-14-2008 02:18 PM
тАО07-14-2008 02:18 PM
DL360 G3 Power Supply issue
I have a DL360 G3 with two power supplies. When one power supply is unplugged, the server hangs on reboot waiting for user confirmation. How can I force the server to boot up without the 2nd power supply plugged in?
Thanks.
Thanks.
3 REPLIES 3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-14-2008 11:00 PM
тАО07-14-2008 11:00 PM
Re: DL360 G3 Power Supply issue
hi
what kind of confirmation?
press F1 to continue?
if so check this
POST F1 Prompt
The POST F1 Prompt option is a toggle setting that configures the server so the F1 key must be pressed to proceed when an error is encountered during the power-up sequence. A series of system tests executes during POST before continuing with the following:
- If failures occur that allow the system to continue operating, the system continues to boot but posts a message.
- If critical components fail or are missing, the server attempts to boot. If it can boot, it posts a message and an F1 prompt.
--- If Enabled is selected and an error occurs, the system stops at the F1 prompt until the F1 key is pressed, before continuing to boot.
--- If Delayed is selected and an error occurs, the system pauses for 20 seconds at the F1 prompt, and then continues to boot the OS.
- If the system cannot run with the missing or failed components, it halts until those components are replaced.
NOTE: The POST F1 Prompt setting is enabled by default in ProLiant ML and DL servers and is disabled by default in BL servers.
regards
what kind of confirmation?
press F1 to continue?
if so check this
POST F1 Prompt
The POST F1 Prompt option is a toggle setting that configures the server so the F1 key must be pressed to proceed when an error is encountered during the power-up sequence. A series of system tests executes during POST before continuing with the following:
- If failures occur that allow the system to continue operating, the system continues to boot but posts a message.
- If critical components fail or are missing, the server attempts to boot. If it can boot, it posts a message and an F1 prompt.
--- If Enabled is selected and an error occurs, the system stops at the F1 prompt until the F1 key is pressed, before continuing to boot.
--- If Delayed is selected and an error occurs, the system pauses for 20 seconds at the F1 prompt, and then continues to boot the OS.
- If the system cannot run with the missing or failed components, it halts until those components are replaced.
NOTE: The POST F1 Prompt setting is enabled by default in ProLiant ML and DL servers and is disabled by default in BL servers.
regards
Didn't your momma teach you to say thanks!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-15-2008 08:33 AM
тАО07-15-2008 08:33 AM
Re: DL360 G3 Power Supply issue
Thanks Karlo, that will do the trick
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-15-2008 09:00 AM
тАО07-15-2008 09:00 AM
Re: DL360 G3 Power Supply issue
Hi,
If the power supply is plugged in but you don't have the power cable attached it will make a circuit and the system will assume there is a fault.
Just pull the second power supply out an inch or two and there will be no circuit and no error message.
Alternatively as Karlo suggests you can prevent the F1 prompt in the BIOS.
Regards,
Brian
If the power supply is plugged in but you don't have the power cable attached it will make a circuit and the system will assume there is a fault.
Just pull the second power supply out an inch or two and there will be no circuit and no error message.
Alternatively as Karlo suggests you can prevent the F1 prompt in the BIOS.
Regards,
Brian
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP