- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- Re: DL360 G7 problem with RAID 5
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-28-2018 02:31 AM
01-28-2018 02:31 AM
DL360 G7 problem with RAID 5
Hello everybody. I have a big problem with DL360 G7, yesterday we turned off our server and after 3 hours turned on again, but server started to reload every 10 sec. We checked status and saw that our logical drive has failed. We have 4 phisical drives, but only three drives light with green color when server reloads. How we understand some our drives was failed, but how we can find out about this drives? Can we save our data if we replace failed drives?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-28-2018 08:30 PM
01-28-2018 08:30 PM
Re: DL360 G7 problem with RAID 5
Hi,
Considering that you have a RAID 5, there should be a fault tolerance of a single drive failure. The screenshots attached does not show if at all there is a drive at fault. There is a need to analyze the ADU report in this case, that you can generate from the Array Configuratoin Utility. Reach out to HPE Support and they can analyze the same and provide an appropriate recommendation.
Regards,
Vador
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-31-2018 03:13 AM
01-31-2018 03:13 AM
Re: DL360 G7 problem with RAID 5
hi, It might be wise to get indeed an formal HPE support case opened up.
In addition feel free to post a readable ADU report here so people can still take a loot at it.
It seems in this case your LD is failed at a controller level but it does not indicate the failed physical drive.
If you server is still booting and working then you could try maybe 1st to verify you have a working back or make one.
Then you could reboot your server as well as sometimes during next reboot and POST it would mark the drives then better as failed. If needed you might have to lookup your Driver, controller FW and disk Fw compatibility to make sure you are in a supported mode between the 3 of that.
Goodluck we hope you can recover in a good and stable state.
Cheers, jeroen