- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- DL380 G3 not able to acess ORCA
ProLiant Servers (ML,DL,SL)
1753638
Members
5846
Online
108798
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-13-2010 01:38 AM
тАО06-13-2010 01:38 AM
DL380 G3 not able to acess ORCA
Hi,
I'm trying to rebuild a DL380 G3. It came with a single 72GB HDD, and I've put in two more. However, when it boots up and the Smart Array 5i initialises, I press to try and get into the ORCA utility to configure the drives and nothing happens. All 3 drives have a green light come on during boot (so I assume that power is getting to them) and when the 5i is initialisng I get 3 spinning pipes, so I think the controller is seeing 3 drives. The system recognises the original drive but I can't get into ORCA. Any ideas please?
I'm trying to rebuild a DL380 G3. It came with a single 72GB HDD, and I've put in two more. However, when it boots up and the Smart Array 5i initialises, I press
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-13-2010 08:51 PM
тАО06-13-2010 08:51 PM
Re: DL380 G3 not able to acess ORCA
is your keyboard OK?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-13-2010 10:59 PM
тАО06-13-2010 10:59 PM
Re: DL380 G3 not able to acess ORCA
Hi,
All systme update with firmware maintanence cd and than try again.
Do you get the controller card with SmartStart CD?
Regards
Erdogan.
All systme update with firmware maintanence cd and than try again.
Do you get the controller card with SmartStart CD?
Regards
Erdogan.
Kind Regards,
Erdogan.
No support by private messages. Please ask the forum!
Erdogan.
No support by private messages. Please ask the forum!
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP