- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- Re: DL380 G4 Firmware update fails.
ProLiant Servers (ML,DL,SL)
1748280
Members
3967
Online
108761
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-29-2007 08:57 AM
тАО05-29-2007 08:57 AM
DL380 G4 Firmware update fails.
On boot, the primary ROM fails and the backup is loaded (message to run ROMPaq).
I've tried running ROMPaq from floppy to load newest ROM and also original, but in either case the process never completes.
I've also tried to update the ROM using a software maintenance ISO (md5sum checked out) without success (seems to timeout at 99%).
System Maintenance Switches S1-S6 are all off.
Is there anything else I can check? Any suggestions?
-Marc
I've tried running ROMPaq from floppy to load newest ROM and also original, but in either case the process never completes.
I've also tried to update the ROM using a software maintenance ISO (md5sum checked out) without success (seems to timeout at 99%).
System Maintenance Switches S1-S6 are all off.
Is there anything else I can check? Any suggestions?
-Marc
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-31-2007 07:56 AM
тАО05-31-2007 07:56 AM
Re: DL380 G4 Firmware update fails.
Marc,
You could try clearing NVRAM and CMOS via Switch 6, then booting SmartStart to reload after changing switch 6 back to disabled position.
Good Luck,
Louis
You could try clearing NVRAM and CMOS via Switch 6, then booting SmartStart to reload after changing switch 6 back to disabled position.
Good Luck,
Louis
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-31-2007 09:28 AM
тАО05-31-2007 09:28 AM
Re: DL380 G4 Firmware update fails.
Thanks for the suggestion Louis, but no change.
HP is sending me a new system board.
-Marc
HP is sending me a new system board.
-Marc
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP