- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- DL380 G7 - DOWN
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-14-2017 03:42 AM
тАО05-14-2017 03:42 AM
DL380 G7 - DOWN
i have dl380 g7 server.When I insert the power cable, the "System Power LED" is amber. When I press the power button the system tries to start. The system fans starts, but after a few secons they stops again, this happens three times. And then the "Health" led is flashing red.
i changed power supply but no effcet.i reset server , pull out ram , cpu , hdd , raid controller but no efect.
any guys can help me?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-14-2017 04:36 AM
тАО05-14-2017 04:36 AM
Re: DL380 G7 - DOWN
Perhaps you can still access your ILO page to see whats wrong?
Does your keybord check show anything? Ifcthe lights stay lit the CPU might have a problem.
Andrew
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-20-2017 01:27 AM - edited тАО05-20-2017 01:41 AM
тАО05-20-2017 01:27 AM - edited тАО05-20-2017 01:41 AM
Re: DL380 G7 - DOWN
I changed cpu , ram , power supply but still have probleam.
port 84 led number 0 is flashing and other led is off
any suggestion?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-07-2017 09:30 AM
тАО06-07-2017 09:30 AM
Re: DL380 G7 - DOWN
Did you check the ILO like the first reply mentioned? It might shed some light.
It could be as simple as some power cabling being slightly loose or the PCI riser being inserted wrong, etc. I've had servers do the same thing in the past and always found something slightly loose (usually after shipping it somewhere). Except once after a BIOS flash went bad, but that was on an old gen 2 Proliant...sad memory there and finally got it working using the floppy disk based BIOS recovery method... not really applicable here.
I assume the CPU/RAM/power you've swapped out all came from a known working supply of spares?
Try limiting it to a single CPU and just one RAM module to eliminate the 2nd socket/mem banks as a potential problem, and maybe even disconnect the power/data from the drive cage just to see if you can get it to boot at all. Try swapping which bay the power supply is plugged in to, etc. etc.
In other words, strip this thing to the bare minimum it needs to be able to boot up and show anything at all, and oh yes, check ILO to see if it recorded any useful info.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-07-2017 06:50 PM
тАО06-07-2017 06:50 PM
Re: DL380 G7 - DOWN
Your problem seem very similar to what i just posted. I have a G6 that exibits the same 3 cycles starts before giving up.
I think mine is due to a false overtemp signal shown by the ILO after it initially failed, and by the front panel overtemp light.
See the 5th entry of this thread:
DL380-g6-shutdown-from-overheating-Zone-19-Location-CPU