- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- Re: DL380 G7 FW.1.28 does not retain configured de...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-04-2012 11:54 AM
09-04-2012 11:54 AM
DL380 G7 FW.1.28 does not retain configured default gateway - reverts to 0.0.0.0
(restatement as new post from http://h30434.www3.hp.com/t5/Other-HP-Consumer-Products-and/DL380-G7-Proliant-not-holding-it-s-Default-Gateway-address-in/m-p/1823491#M8352)
Issue: DL380 G7 at Firmware revision 1.28 does not retain a statically configured default gateway, but instead reverts to 0.0.0.0
i investigated the advisory given in a previous post (c03283274) and while it fits my situation exactly, I can unequivocally state that it is NOT a "display only" issue in this case.
I have 2 x dl380 g7s in the same rack, both at the same firmware revision of 1.28, i am using the same IPs and cables (sequentially, of course), and the second server stubbornly refuses to accept the default gateway i give it and also does not respond from the switch to which it is connected (which it would if, as the advisory states, it is really there, just not showing itself.)
I have attempted to "trick" it from a number of angles, assuming the correctness of the advisory, that there is some point at which it puts it in the bucket though it is not visible (eg. reset, re-enter / reset to defaults, reboot, re-enter / reset to defaults, shutdown, unplug, re-enter / cycle through the ancillary transceiver options in concert with the ip config / enter an entirely bogus gateway, attempt save, fail, enter correct gateway / etc.)
I offer this long-winded set to hopefully forestall any of the more obvious questions of troubleshooting on my part, but the short-and-sweet is the 0.0.0.0 gateway being displayed across F10 saves is very obviously acting as a blank in the active configuration of the dl380 g7 ilo3 in question.
Do you have any further insight? I have found no more questioning of this issue on the web. (Possibly b/c others were able to get around this with a direct connect laptop more forgiving of a missing gateway than a switchport. I do not have this option.)
thanks -
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-05-2012 07:55 AM
09-05-2012 07:55 AM
Re: DL380 G7 FW.1.28 does not retain configured default gateway - reverts to 0.0.0.0
We fixed it in iLO3 v1.29 that is only available on FTP. See link below.
ftp://il0t3st:G1vme1LO@ftp.usa.hp.com/ilo3/1.29/
__________________________________________________
If you feel this was helpful please click the KUDOS! thumb below!
- Tags:
- iLO
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-16-2012 08:16 AM
10-16-2012 08:16 AM
Re: DL380 G7 FW.1.28 does not retain configured default gateway - reverts to 0.0.0.0
I also have this problem, but that FTP link is dead - can you repost the fix?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-16-2012 10:28 AM - edited 10-16-2012 10:32 AM
10-16-2012 10:28 AM - edited 10-16-2012 10:32 AM
Re: DL380 G7 FW.1.28 does not retain configured default gateway - reverts to 0.0.0.0
iLO3 1.50 containing the fix is available on the FTP
Online ROM Flash Component for Windows 64-bit
ftp://ftp.hp.com/pub/softlib2/software1/sc-windows-fw-ilo/p1728391553/v73058
Online ROM Flash Component for Windows 32-bit
ftp://ftp.hp.com/pub/softlib2/software1/sc-windows-fw-ilo/p901462262/v73059
Online ROM Flash Component for Linux
ftp://ftp.hp.com/pub/softlib2/software1/sc-linux-fw-ilo/p1255562964/v73060
Note: Please clear the browser cache after upgrading to version 1.50. There are lots of changes to the iLO webGUI in this version.
__________________________________________________
If you feel this was helpful please click the KUDOS! thumb below!