- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- Re: DL380 Gen 10 SW raid drivers
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-20-2018 09:14 AM
тАО03-20-2018 09:14 AM
DL380 Gen 10 SW raid drivers
I had used the raid drivers before to install Server 2016 on our server. The server suffered a hardware failure and the motherboard was replaced under warenty. But windows would no longer boot. We figured it was due to dissimilar firmware, or just windows being crabby.
When I booted to the windows 2016 install media through ILO I attempted to inject the SW Raid drivers as I had done before. The drivers showed up, but wondows would no longer accept them.
The VID was apparently removed from Gen 10 severs for what reason I will never know. So injecting the driver is my only option at this point.
I tried drivers from both the folowing links to no avail
Please advise
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-20-2018 12:52 PM - edited тАО03-20-2018 01:02 PM
тАО03-20-2018 12:52 PM - edited тАО03-20-2018 01:02 PM
Re: DL380 Gen 10 SW raid drivers
I did it several Times.
Download the Driver, extract, mount the Driectory as iLO Folder and add it at the Storage Driver Setup section.
This should work, if not, something is wrong.
May be the new Mainboard have different settings.
Generate a AHS Logfile and give it to Support to check it, for Hardware problems.
Is the SR100 enabled in BIOS, is the BIOS in same state (legacy, UEFI)?
NOTE: HPE Smart Array S100i SR Gen10 SW RAID will operate in UEFI mode only.
NOTE: HPE Smart Array S100i SR Gen10 SW RAID is off by default and must be enabled.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-12-2018 05:57 AM
тАО11-12-2018 05:57 AM
Re: DL380 Gen 10 SW raid drivers
I experienced the same thing like this
hello, can you help me?