ProLiant Servers (ML,DL,SL)
cancel
Showing results for 
Search instead for 
Did you mean: 

DL580 G1 Server 177 Configuration not complete Error

SOLVED
Go to solution
Aravamuthan
Occasional Advisor

DL580 G1 Server 177 Configuration not complete Error

Hi, we have problem with our DL580 G1 server, it was given error while rebooting "177 Configuration not complete controller order not setup. press F1 to continue. we press F1 server boots up but immediately gives blue dump and restarts. we try F10 key but we got "Not valid partition found message". Server is production server and storage was connected in Smart Array 5300 controller. Kindly help how to close the issue. we got 5300 Raid controller battery has low charge message.
10 REPLIES

Re: DL580 G1 Server 177 Configuration not complete Error

Hi,

Check the following settings and disks.

1.Power up the server.
The server runs the POST sequence, and briefly displays a
prompt for RBSU.
2.At the prompt, press the F9 key to start RBSU.
3.Follow the on-screen instructions to configure the system and
to set the boot controller order.
4.Save the configuration and exit from the utility.
5.Restart the server for the new settings to take effect.
PF Servers
---
1. Reboot the server. The POST sequence begins, and an ORCA prompt message is
briefly displayed.
2. Press the F8 key to start ORCA.
3. On the Main Menu screen, select Select as Boot Controller.
4. Follow the remaining prompts to set the currently selected controller as the boot
controller for the system.

That will also fix the problem :) Remember to assign points to answers that helped in your problem. So the forum stays alive...

Regards.
Erdogan
Kind Regards,
Erdogan.
I am HPE Employee

If this helps you with your issue, please click the thumb to register a Kudo.
If it resolves the issue, please consider marking it as an Accepted Solution.
The comments in this post are my own and do not represent an official reply from the company. No warranty or guarantees of any kind are expressed in my reply.
Aravamuthan
Occasional Advisor

Re: DL580 G1 Server 177 Configuration not complete Error

Hi, F9 key is not responding, pls let me know any other option is there to go in to RBSU
Johan Guldmyr
Honored Contributor
Solution

Re: DL580 G1 Server 177 Configuration not complete Error

It should say in the POST what button to press.. what about the DEL button or maybe that was never used on servers?

F1, F8, F9, F10.. it varies.
Aravamuthan
Occasional Advisor

Re: DL580 G1 Server 177 Configuration not complete Error

Hi, Thank you for your support, i have corrected this error with help of smart start CD. Now i got error while booting the OS, it was "Hardware Malfunction call vendor" message displayed with blue screen or some time Blue screen dump and restarted. please help what to do for this issue. i done a physical check inside the server for any ampher indication, but noting no indication found. please help....
Johan Guldmyr
Honored Contributor

Re: DL580 G1 Server 177 Configuration not complete Error

If you run the smartstart diagnostics, do you get any errors?
Aravamuthan
Occasional Advisor

Re: DL580 G1 Server 177 Configuration not complete Error

Hi, The diagnostic utility did't find any error on the server.
Johan Guldmyr
Honored Contributor

Re: DL580 G1 Server 177 Configuration not complete Error

Maybe you can try to run the server in minimal configuration and see if it's possible to isolate the problematic part..

Re: DL580 G1 Server 177 Configuration not complete Error

Memory and pci slot check or pci device slots change.
Kind Regards,
Erdogan.
I am HPE Employee

If this helps you with your issue, please click the thumb to register a Kudo.
If it resolves the issue, please consider marking it as an Accepted Solution.
The comments in this post are my own and do not represent an official reply from the company. No warranty or guarantees of any kind are expressed in my reply.
Aravamuthan
Occasional Advisor

Re: DL580 G1 Server 177 Configuration not complete Error

Thank you to all, i will sort out the issue, it was memory bank problem one of the memory module given error & the same replaced now server working fine. Thanks for the support.
Johan Guldmyr
Honored Contributor

Re: DL580 G1 Server 177 Configuration not complete Error

Great, please don't forget to assign points here in the forum :)