- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- Re: Dl 180 G6 can not boot after install NC522SPF
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-17-2009 01:42 AM
тАО09-17-2009 01:42 AM
Dl 180 G6 can not boot after install NC522SPF
When I plug it, the system shows me that the BMC SDRR is reconfigured. It updates from 2.17.0.199 to 2.17.0.194.
I also check the RBSU, the hard/disk boot Smart Array is dissapeared and after the boot screen, only a white cursor is blink in a blank screen. It can't boot.
When I plug out the NC522SPF, windows server 2008 boot normally.
What can I do to solve this problem?
Thanks a lot.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-17-2009 04:14 AM
тАО09-17-2009 04:14 AM
Re: Dl 180 G6 can not boot after install NC522SPF
Only thing I saw about it was that it requires 2GB RAM per NIC installed..
One thing you could try would be to try to install it in the other PCI slot?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-17-2009 04:32 AM
тАО09-17-2009 04:32 AM
Re: Dl 180 G6 can not boot after install NC522SPF
And it fails with the same error.
I can't understand it.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-17-2009 04:36 AM
тАО09-17-2009 04:36 AM
Re: Dl 180 G6 can not boot after install NC522SPF
If you have another server you could try it there. Or if you have another PCIe card you can see if that works in the slot.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-17-2009 06:41 AM
тАО09-17-2009 06:41 AM
Re: Dl 180 G6 can not boot after install NC522SPF
I try to plug these card in another server (DL360 G5) and it works properly.
I don't know how can I clear the NVRAM!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-17-2009 06:51 AM
тАО09-17-2009 06:51 AM
Re: Dl 180 G6 can not boot after install NC522SPF
It is located on the same "level/height" as the small PCIe slot and to the edge of the system board.
You could also possible do this via the RBSU or the BIOS after loading the computer. Just make sure you don't erase your whole system.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-17-2009 07:34 AM
тАО09-17-2009 07:34 AM
Re: Dl 180 G6 can not boot after install NC522SPF
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-17-2009 11:52 AM
тАО09-17-2009 11:52 AM
Re: Dl 180 G6 can not boot after install NC522SPF
hi,
the nic is listed in quickspecs
http://h18004.www1.hp.com/products/quickspecs/13248_na/13248_na.html#Additional%20Options
HP NC522SFP Dual Port 10GbE Server Adapter
NOTE: A minimum of two Gigabytes (2 GB) of server memory is required per each NC522SFP adapter.
if all firmwares are in place , reboot server select bios defaultsnow with no ram or pci cards at all reboot
then again reboot with ram only ensure this is hp ram important not just compatible,:)
now install card with MIN memory allowed for the nic 2gb
a secondary note
did you use this cd ?
Easy Set-up CD
Easy Set-up CDs are available on all 100-series G6 servers and are also available as an ISO image web download. HP ProLiant Easy Set-up CDs provide easy, step-by-step, single and multi-server server utilities for the ProLiant 100-series G6 servers to streamline server setup for 100-series G6 servers. The user experience is consistent with SmartStart and offers the following capabilities
if the above is done and post does not complete looks like a dud nic, only other reasonable step is to try it in a another server, to ensure this , and of course to trya compatible nic from quickspecs for cros verifiction,,
let us know results
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-18-2009 08:01 AM
тАО09-18-2009 08:01 AM
Re: Dl 180 G6 can not boot after install NC522SPF
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-18-2009 08:36 AM
тАО09-18-2009 08:36 AM
Re: Dl 180 G6 can not boot after install NC522SPF
Thanks to everybody, but its no possible to solve this problem.
I just talk with HP Support and they says me that the motherboard is damaged and it must be changed.
On monday I will have a technician to do it.
Thanks for you time!