E200i logical drive extend fails

[angunguak]

Hi,

A customer of mine has an old ML350G5 that needed af disk upgrade in a 2-disk RAID 1+0. The disks were replaced one by one from 240GB to two 500GB.

Afterwards I wanted to extend the LUN and ran into a problem with ACUCLI, where the extend could not succeed.

Any help highly appreciated:

=> controller slot=0 logicaldrive 2 modify size=max

Warning: Extension may not be supported on certain operating systems.
Performing extension on these operating systems can cause data to
become inaccessible. See ACU documentation for details. Continue?
(y/n) y

Error: This operation is not supported with the current configuration. Use the
"show" command on devices to show additional details about the
configuration.

=> controller all show config detail

Smart Array E200i in Slot 0
Bus Interface: PCI
Slot: 0
Serial Number: QT83MQ3763
RAID 6 (ADG) Status: Disabled
Controller Status: OK
Chassis Slot:
Hardware Revision: Rev A
Firmware Version: 1.72
Rebuild Priority: Medium
Expand Priority: Medium
Surface Scan Delay: 15 sec
Cache Board Present: True
Cache Status: OK
Accelerator Ratio: 100% Read / 0% Write
Drive Write Cache: Disabled
Total Cache Size: 64 MB
Battery Pack Count: 0
SATA NCQ Supported: False

Array: A
Interface Type: SATA
Unused Space: 0 MB
Status: OK

Logical Drive: 1
Size: 232.9 GB
Fault Tolerance: RAID 1+0
Heads: 255
Sectors Per Track: 32
Cylinders: 59844
Stripe Size: 128 KB
Status: OK
Array Accelerator: Enabled
Unique Identifier: 600508B1001037363320202020200003
Disk Name: \\.\PhysicalDrive0
Mount Points: C:\ 48.8 GB, G:\ 184.0 GB
Logical Drive Label: A000050EQT83MQ3763 1124

physicaldrive 1I:1:1
Port: 1I
Box: 1
Bay: 1
Status: OK
Drive Type: Data Drive
Interface Type: SATA
Size: 250 GB
Firmware Revision: 20.06C06
Serial Number: WD-WCANY4124933
Model: ATA WDC WD2500YS-70S
SATA NCQ Capable: False
PHY Count: 1
PHY Transfer Rate: 1.5GBPS
physicaldrive 1I:1:2
Port: 1I
Box: 1
Bay: 2
Status: OK
Drive Type: Data Drive
Interface Type: SATA
Size: 250 GB
Firmware Revision: 20.06C06
Serial Number: WD-WCANY3744212
Model: ATA WDC WD2500YS-70S
SATA NCQ Capable: False
PHY Count: 1
PHY Transfer Rate: 1.5GBPS

Array: B
Interface Type: SATA
Unused Space: 476934 MB
Status: OK

Logical Drive: 2
Size: 232.9 GB
Fault Tolerance: RAID 1+0
Heads: 255
Sectors Per Track: 32
Cylinders: 59844
Stripe Size: 32 KB
Status: OK
Array Accelerator: Enabled
Unique Identifier: 600508B1001037363320202020200004
Disk Name: \\.\PhysicalDrive1
Mount Points: E:\ 232.8 GB
Logical Drive Label: A286973DQT83MQ3763 DE59

physicaldrive 1I:1:3
Port: 1I
Box: 1
Bay: 3
Status: OK
Drive Type: Data Drive
Interface Type: SATA
Size: 500.1 GB
Firmware Revision: HPG3
Serial Number: 9QG835Z6
Model: ATA GB0500C4413
SATA NCQ Capable: False
PHY Count: 1
PHY Transfer Rate: 1.5GBPS
physicaldrive 1I:1:4
Port: 1I
Box: 1
Bay: 4
Status: OK
Drive Type: Data Drive
Interface Type: SATA
Size: 500.1 GB
Firmware Revision: HPG3
Serial Number: 9QG846GG
Model: ATA GB0500C4413
SATA NCQ Capable: False
PHY Count: 1
PHY Transfer Rate: 1.5GBPS

=> ctrl all show status

Smart Array E200i in Slot 0
Controller Status: OK
Cache Status: OK

=> ctrl slot=0 ld all show

Smart Array E200i in Slot 0

array A

logicaldrive 1 (232.9 GB, RAID 1+0, OK)

array B

logicaldrive 2 (232.9 GB, RAID 1+0, OK)