- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- Re: Error report
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-07-2005 08:50 AM
тАО03-07-2005 08:50 AM
Error report
Is in PL3000
SCSI port 1 Drive 2 is not stamped for monitoring.
SCSI port 1 Drive 10 is not stamped for monitoring.
SCSI port 1 Drive 11 is not stamped for monitoring.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-07-2005 09:05 PM
тАО03-07-2005 09:05 PM
Re: Error report
regards,
Akos
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-22-2005 07:05 AM
тАО03-22-2005 07:05 AM
Re: Error report
Server Model: ML350 G4
Array Controller: SmartArray 642 (RAID 5 setting)
Disk Drive Model: BD07287B4C (x6 disks in the array)
I just upgraded the firmware on the array controller (to version 2.34) and disks (to version HPB5A) using the most recent downloads on the website.
I found a PDF which describes the problem, but I cannot seem to be able to implement the solution:
http://docs.hp.com/en/338615-002/338615-002.pdf
This article suggests that I "Run ACU" and "change the array accelerator size and save the configuration" however I do not see an option to change the accelerator size anywhere! I am only able to "Enable" or "Disable" the Accelerator. I have also looked into the Command Line Interface (CLI) version of the ACU and do not see any way to change the accelerator size.
I am using Windows Server 2003 (Standard) and used SmartStart 7.20 to install the OS. Every piece of hardware in the server is standard HP hardware. Thanks for any tips or help!
Jared
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-22-2005 08:04 AM
тАО03-22-2005 08:04 AM
Re: Error report
If you can't change the accelerator size, simply change the rebuild rate, save it and then put it back to what it was. Any change to the controller setting should stamp the drive once you have saved it. This is true for the standalone ACU, I'm not sure about the web based ACU though but try it and see.
I hope this helps.
Brian
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-23-2005 05:36 AM
тАО03-23-2005 05:36 AM
Re: Error report
Perhaps I'm using a different version of the ACU? I'm using 7.20.19.0, accessing it via "Start > Programs > HP System Tools > HP Array Configuration Utility > HP Array Configuration Utility
I have also tried rebooting to the SmartStart CD and I seem to get the same tool.
Thanks again for any help! =)