- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- Re: H.D.D mirror problem
ProLiant Servers (ML,DL,SL)
1748204
Members
3563
Online
108759
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
12-22-2006 02:46 PM
12-22-2006 02:46 PM
H.D.D mirror problem
Hi There
We have configufe H/W mirror DL360 g4p server with SATA H.D.D. and configure OS MS 2003 Enterprise Edition with SP2. After configure the system we checked the hardware mirror of the system. But when unplug systems bay 0 H.D.D it boot and run the OS smoothly. Then shutdown the system and plug systems bay 0 H.D.D and unplug the bay 1 H.D.D the systems boot not found the OS.
Server:HP DL 360 g4p
OS: Windows 2003 ENT
H.D.D:250GB 7.2K ATA SATA
RAID Controller: Embedded SATA Controller
Please help me to how can i break the H.D.D mirror and then how can i built the new one hardware mirror.
Thanks and regards
Md.Mazharul Hoque.
We have configufe H/W mirror DL360 g4p server with SATA H.D.D. and configure OS MS 2003 Enterprise Edition with SP2. After configure the system we checked the hardware mirror of the system. But when unplug systems bay 0 H.D.D it boot and run the OS smoothly. Then shutdown the system and plug systems bay 0 H.D.D and unplug the bay 1 H.D.D the systems boot not found the OS.
Server:HP DL 360 g4p
OS: Windows 2003 ENT
H.D.D:250GB 7.2K ATA SATA
RAID Controller: Embedded SATA Controller
Please help me to how can i break the H.D.D mirror and then how can i built the new one hardware mirror.
Thanks and regards
Md.Mazharul Hoque.
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
12-24-2006 02:46 AM
12-24-2006 02:46 AM
Re: H.D.D mirror problem
Sounds to me as if when you removed the drive 0, the controller 'failed' the drive in its setup. When you replaced the drive and removed the drive 1, drive 0 was still set as 'failed' and it would start to rebuild the mirror, but now drive 1 is 'failed', so now the entire array has failed.
To get back you will probably have to delete the RAID logical entirely, configure a new set with both drives install, but do not Initialize or format the logical, just reboot
To get back you will probably have to delete the RAID logical entirely, configure a new set with both drives install, but do not Initialize or format the logical, just reboot
Hot Swap Hard Drives
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP