ProLiant Servers (ML,DL,SL)
cancel
Showing results for 
Search instead for 
Did you mean: 

HP DL 360g4 SMart Array

 
jmrhenus
Occasional Visitor

HP DL 360g4 SMart Array

Hallo,

on a 360g4 one hardisk was broken, I replace this Hard Disk with a new one and the Rebuild of Raid1 was starting, but some min. later it`s stopped, the led-light from the hard disk goes off and the crontoller status is now: "Ready for Rebuild", but nothing happend. I tried this few times but always the same message.

Please can someone help me?

Thank You
5 REPLIES
gregersenj
Honored Contributor

Re: HP DL 360g4 SMart Array

Check, wich HDD ID it is waiting for, and if the other disk got a problem.

Use ACU, Array configuration Utility.
for the ID

Use the SMH, System Management Homepage, to see statistics of the other drive.

BR
/jag
gregersenj
Honored Contributor

Re: HP DL 360g4 SMart Array

Or have simply taken the Array Controller out of interim recovery mode?
If so, it should be possible to start rebuild from the ACU.

BR
/jag
jmrhenus
Occasional Visitor

Re: HP DL 360g4 SMart Array

how can I bring out the array controller to the status. (interim recovery mode)?

Log:
Smart Array 6i in Slot 0
Bus Interface: PCI
Slot: 0
RAID 6 (ADG) Status: Disabled
Controller Status: OK
Chassis Slot:
Hardware Revision: Rev B
Firmware Version: 2.84
Rebuild Priority: High
Expand Priority: Low
Surface Scan Delay: 15 sec
Cache Board Present: True
Cache Status: OK
Accelerator Ratio: 100% Read / 0% Write
Total Cache Size: 64 MB
Battery Pack Count: 0
SATA NCQ Supported: False

Array: A
Interface Type: Parallel SCSI
Unused Space: 0 MB
Status: OK

Logical Drive: 1
Size: 67.8 GB
Fault Tolerance: RAID 1+0
Heads: 255
Sectors Per Track: 32
Cylinders: 17433
Stripe Size: 128 KB
Status: Ready for Rebuild
Array Accelerator: Enabled
Unique Identifier: 600508B1001FFFFFA00003418EC70002
Disk Name: /dev/cciss/c0d0
Mount Points: none 956 MB, /boot 94 MB, / 4.7 GB, /opt 3.7 GB, /usr 3.7 GB, /var 4.7 GB, /var/log 956 MB, /tmp 956 MB

physicaldrive 1:0
SCSI Bus: 1
SCSI ID: 0
Status: OK
Drive Type: Data Drive
Interface Type: Parallel SCSI
Transfer Mode: Ultra 320 Wide
Size: 72.8 GB
Transfer Speed: 320 MB/Sec
Rotational Speed: 10000
Firmware Revision: HPB2
Serial Number: AAL1P530608U0510
Model: COMPAQ BD0728856A
physicaldrive 1:1
SCSI Bus: 1
SCSI ID: 1
Status: OK
Drive Type: Data Drive
Interface Type: Parallel SCSI
Transfer Mode: Ultra 320 Wide
Size: 72.8 GB
Transfer Speed: 320 MB/Sec
Rotational Speed: 10000
Firmware Revision: HPB7
Serial Number: 3HZ0VF6200007334EFKT
Model: COMPAQ BD07285A25
gregersenj
Honored Contributor

Re: HP DL 360g4 SMart Array

Are you running linux?

try to do a show config

and check the result.
gregersenj
Honored Contributor

Re: HP DL 360g4 SMart Array

You could remove the new disk.
Do a reboot, and check that the array contoller come up in interim recovery mode.
the add the new disk.

but still do the show config, to verify ID's