- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- Re: HP DL 380 G5 - SLB
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-08-2007 06:42 PM
тАО11-08-2007 06:42 PM
HP DL 380 G5 - SLB
We have 2 NICs on HP DL 380 G5 server running Win2K3-R2. I want to configure SLB for same. Drivers are updated to the latest.
I connected both the NIC to Cisco 3560G-L3 switch. I selected the SLB option in the HP Network conf utility with all defaults.
Switch is configured as below for both ports,
config t
interface range 0/19 - 20
no ip address
no switchport
channel-group 10 mode on
end
config t
port-channel load-balance src-dst-ip
end
I am not able to connect to the server. Ping does not work.
Please guide what could be the cause and troubleshoot.
Thanks,
Sid.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-08-2007 06:55 PM
тАО11-08-2007 06:55 PM
Re: HP DL 380 G5 - SLB
While enabling the SLB in the Network Configuration utility you can enable the SLB either using the layer 2 or layer 3. try enabling the layer 2 that is instead of ip address configure load balancing using the mac address on both sides and check.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-08-2007 07:29 PM
тАО11-08-2007 07:29 PM
Re: HP DL 380 G5 - SLB
I tried to configure it as below,
config t
port-channel load-balance src-dst-mac
end
config t
interface range gig 0/19 - 20
switchport
switchport mode access
channel-group 10 mode on
At the channet-group command i get the error as -
Command rejected (Port-channel10, Gi0/19): Either port is L2 and port-channel is
L3, or vice-versa
% Range command terminated because it failed on GigabitEthernet0/19
Please guide
Thanks,
Sid.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-08-2007 07:51 PM
тАО11-08-2007 07:51 PM
Re: HP DL 380 G5 - SLB
I skipped to add the vlan on that ports. After adding the ports to vlan, i am able to communicate with the server !!! :P
But i am not able to set the channel-group option.
I can configure channel-group only with "no switchport" option. With that command i am not able to add the port in its vlan.
The configuration now is as below
interface range 0/19 - 20
switchport access vlan 101
switchport mode access
Please guide.
Thanks,
Sid.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-08-2007 08:09 PM
тАО11-08-2007 08:09 PM
Re: HP DL 380 G5 - SLB
The problem is resolved. The channel-group 10 was L3. Creating a new channel-group 20, L2, resolved it. The configuration now is -
config t
port-channel load-balance src-dst-ip
end
config t
interface range gig 0/19 - 20
no ip address
switchport mode access
switchport access vlan 101
channel-group 20 mode on
end
Thanks
Sid.