- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- HP DL380 G4 Boot problem
ProLiant Servers (ML,DL,SL)
1753808
Members
8047
Online
108805
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-15-2006 01:10 AM
тАО05-15-2006 01:10 AM
HP DL380 G4 Boot problem
Guys
I unpacked a new DL380 this morning and it boots up fine with the array controller and memory. If I boot with the SmartStart CD it loads the CD with all the dots and then just reboot. I have tried another CD and I tried the Firmware CD. No luck its just go into a loop. The firmware is one lvl down and the array controller is on the lastest. I have replaced the system board but still no luck.
Any suggestions
I was thinking of the following
- Proc
- Proc power module
- backplane board where drives plug into
Thank
Andre
I unpacked a new DL380 this morning and it boots up fine with the array controller and memory. If I boot with the SmartStart CD it loads the CD with all the dots and then just reboot. I have tried another CD and I tried the Firmware CD. No luck its just go into a loop. The firmware is one lvl down and the array controller is on the lastest. I have replaced the system board but still no luck.
Any suggestions
I was thinking of the following
- Proc
- Proc power module
- backplane board where drives plug into
Thank
Andre
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-15-2006 08:36 AM
тАО05-15-2006 08:36 AM
Re: HP DL380 G4 Boot problem
Hi,
is there any led status on the server at the time of reboot.
Can you boot the server with the aatched offline iml dos reader and check is there any H/W errors on the server.
Prashant S.
is there any led status on the server at the time of reboot.
Can you boot the server with the aatched offline iml dos reader and check is there any H/W errors on the server.
Prashant S.
Nothing is impossible
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-15-2006 06:13 PM
тАО05-15-2006 06:13 PM
Re: HP DL380 G4 Boot problem
Hi
If I take the lid off and boot the server all the green light that is marked is green. No failed parts (fans, drives, proc) I have cleared the cmos and changed the CD rom drive.
The server boots up fine it just do not want to load the Smartstart CD 7.40 and the firmware cd 7.40. Even if I boot with Windows 2003 it loads all the drivers and as it say starting windows it blue screens (think Bad_pool_)
Andre
If I take the lid off and boot the server all the green light that is marked is green. No failed parts (fans, drives, proc) I have cleared the cmos and changed the CD rom drive.
The server boots up fine it just do not want to load the Smartstart CD 7.40 and the firmware cd 7.40. Even if I boot with Windows 2003 it loads all the drivers and as it say starting windows it blue screens (think Bad_pool_)
Andre
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP