- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- Re: HP ProLiant DL160 Gen9 install centos 6.9 64 b...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-27-2017 11:49 PM
тАО08-27-2017 11:49 PM
HP ProLiant DL160 Gen9 install centos 6.9 64 bit
I have a server HP ProLiant DL160 Gen9 with two 2TB disks , and create raid 1 ok but when I install cent6.9 , I still see two disks ? I setup raid 1 , It should be only one 2 TB disk and why I see two disks ? thank you .
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-28-2017 03:45 AM
тАО08-28-2017 03:45 AM
Re: HP ProLiant DL160 Gen9 install centos 6.9 64 bit
CentOS 6.9, the operating system you're installing, has no knowledge of the Logical RAID Volume you created - during the pre-installation phase - using the HPE SSA or HPE Intelligent Provisioning method against the Smart Array Controller your HPE ProLiant DL160 Gen9 Server has (is it the HPE Dynamic Smart Array B140i Controller? ...you didn't specified the Smart Array Controller model your Server is equipped with and it is currently using to manage its disks)...thus you need to inject the correct Smart Array Controller's driver during CentOS 6.9 installation phase.
Assuming your Server is using the HPE Dynamic Smart Array B140i Controller (which is the default Entry level SATA RAID Controller) then you need to arrange your CentOS 6.9 installation by injecting the latest proper hpdsa storage controller driver (HP Dynamic Smart Array B140i SATA RAID Controller Driver) found here (note: it is valid for RedHat Linux Enterprise Server for which there is a binary compatibility with CentOS...at least if you consider same versions of both operating systems, like RHEL 6.9 versus CentOS 6.9).
Instructions on how to install Device Drivers on Linux (RedHat Enterprise Linux 6) can be found on page 9 of HPE Dynamic Smart Array B140i Controller User Guide here.
I'm not an HPE Employee
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-28-2017 09:00 PM
тАО08-28-2017 09:00 PM
Re: HP ProLiant DL160 Gen9 install centos 6.9 64 bit
I install successfully , but reboot and show "error 24 Attempt to access block outside partition " Press any key to continue .
Any advise ??
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-29-2017 12:06 AM
тАО08-29-2017 12:06 AM
Re: HP ProLiant DL160 Gen9 install centos 6.9 64 bit
I installed successfully. thank you very much