- Community Home
- >
- Servers and Operating Systems
- >
- ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- HP Smart Array P440ar disk Non authenticated after...
-
- Forums
-
- Advancing Life & Work
- Advantage EX
- Alliances
- Around the Storage Block
- HPE Ezmeral: Uncut
- OEM Solutions
- Servers & Systems: The Right Compute
- Tech Insights
- The Cloud Experience Everywhere
- HPE Blog, Austria, Germany & Switzerland
- Blog HPE, France
- HPE Blog, Italy
- HPE Blog, Japan
- HPE Blog, Middle East
- HPE Blog, Russia
- HPE Blog, Saudi Arabia
- HPE Blog, South Africa
- HPE Blog, UK & Ireland
-
Blogs
- Advancing Life & Work
- Advantage EX
- Alliances
- Around the Storage Block
- HPE Blog, Latin America
- HPE Blog, Middle East
- HPE Blog, Saudi Arabia
- HPE Blog, South Africa
- HPE Blog, UK & Ireland
- HPE Ezmeral: Uncut
- OEM Solutions
- Servers & Systems: The Right Compute
- Tech Insights
- The Cloud Experience Everywhere
-
Information
- Community
- Welcome
- Getting Started
- FAQ
- Ranking Overview
- Rules of Participation
- Tips and Tricks
- Resources
- Announcements
- Email us
- Feedback
- Information Libraries
- Integrated Systems
- Networking
- Servers
- Storage
- Other HPE Sites
- Support Center
- Aruba Airheads Community
- Enterprise.nxt
- HPE Dev Community
- Cloud28+ Community
- Marketplace
-
Forums
-
Blogs
-
Information
-
English
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
11-22-2018 01:20 AM
11-22-2018 01:20 AM
Hello,
I have a problem with my HP ProLiant ML350 Gen9 server. After update firmware P440ar one of eight oryginal disks (HP 1TB MM1000FBFVR) is alerting. Logs below:
Warning: Device carrier authentication failed. This is not an authentic HPE carrier. I/O operations to the device will not be affected, but the Smart Array controller will not control the LEDs to this device.
Option ROM POST Information: 1709-Slot 0 Drive Array - One or more drives could not be authenticated as genuine drives. Smart Array will not control the LEDs to these drives.
I tried to replace disk slots, downgrade firmware but problem still exists. Problem exist since I removed these disk from slot and move it again.
P.S
Server does not have SAS Expander, only Smart Array Controller P440ar
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
11-23-2018 07:25 AM
11-23-2018 07:25 AM
Re: HP Smart Array P440ar disk Non authenticated after update and remove disk
Hello Mark14,
Please try some bacic troubleshooting steps,
1. Shut down the server and remove the power cord.
2. Reseat all hard drives.
3. Reseat smart array controller ,cables between the controller and drive cage.
4. Please update the firmwares by using below Service Pack for ProLiant(SPP) Version 2018.09.0
https://support.hpe.com/hpsc/swd/public/detail?swItemId=MTX_f5b44d8af3f8451bb72bc3357e
If issue is persist after performed the above steps ,please get it log a support case with HPE for further troubleshooting/Log analysis
I am an HPE Employee
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
11-28-2018 05:00 AM
Hewlett Packard Enterprise International
- Communities
- HPE Blogs and Forum
© Copyright 2021 Hewlett Packard Enterprise Development LP