- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- Re: HP version control agent
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-24-2009 06:51 AM
тАО03-24-2009 06:51 AM
I just installed Server 2003 on a new ML310 with SmartStart 8.15 x32. I am getting an error message concerning the HP version control agent service in event viewer stating that the service failed to load because the application configuration is incorrect.
Any help on this will be appreciated.
Thanks
Bob
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-24-2009 08:19 AM
тАО03-24-2009 08:19 AM
Re: HP version control agent
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-24-2009 09:28 AM
тАО03-24-2009 09:28 AM
Re: HP version control agent
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-24-2009 10:24 AM
тАО03-24-2009 10:24 AM
Re: HP version control agent
basically VCA gathers the data of your current inventory and compares it againts the VCRM, if no VCRM is configure it will always have a yellow bang which is ok because it cannot compare to something, if VCA and VCRM have the same versions it will show an ok next to it, if the VCA detecs something older than what the VCRM has, it will set an action (you decide this action) like upgrade, notify, ignore...
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-24-2009 12:44 PM
тАО03-24-2009 12:44 PM
Re: HP version control agent
Thanks bob
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-24-2009 12:57 PM
тАО03-24-2009 12:57 PM
Re: HP version control agent
sscd does not set this up because, to clear this yellow bang, it will have to install the VCRM on every single deployment and again, useless
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-24-2009 01:13 PM
тАО03-24-2009 01:13 PM
Re: HP version control agent
I see the version control Agent is working fine on my other ML310 and I don't think I did anything but install SmartStart but that was 2 years ago now. If I go into on the older server, it just shows all my current HP software and their version. Can I at least get to that point on the new server.
Thanks for your help here,
Bob
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-24-2009 01:57 PM
тАО03-24-2009 01:57 PM
Solution- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-24-2009 02:07 PM
тАО03-24-2009 02:07 PM
Re: HP version control agent
Thanks Bob
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-24-2009 02:58 PM
тАО03-24-2009 02:58 PM
Re: HP version control agent
"To recover from this issue if it has already occurred, install Windows Server 2003 Service Pack 1 (SP1) after a SmartStart Assisted installation of the operating system using SmartStart Release 8.00. Then, reinstall the VC Agent."