ProLiant Servers (ML,DL,SL)

HPE ML150 G6-Noisy Fan

 
Halit
New Member

HPE ML150 G6-Noisy Fan

hi

sorry for my bad english

my hpe ml150 gen6 has always noisy but today i cleaned it up but right now ists incredibly noisy i checkd errors with hp diagnostic program and it gave this report but i do not understand it very well. could you tell me whats the problem

 

Diagnostic Report Information ACU Version 9.30.15.0 Diagnostic Module Version 6.1.19.0 INFOMGR Version 6.1.29.0 Time Generated Monday July 27, 2020 5:54:58PM   Top-Level Controller(s)    Smart Array P410 in slot 4   Consolidated Error Report Smart Array P410 in slot 4 : Physical Drive (0 MB SAS) 1I:3  The physical drive has failed. Smart Array P410 in slot 4 : Logical Drive 1  Logical drive state: This logical drive has failed and cannot be used. All data on this logical drive has been lost.  [ Top ] → Smart Array P410 in slot 4 Report Section(s): Identify Controller
Cache Config Status
Controller Parameters
Maintenance Operation
MNP Status
Monitor and Performance Violations
SubSystem Parameters
Surface Status
Sense Expansion Ability
VPD Page 80 - Serial Number
VPD Page 83 - Array Information
Controller NVRAM
RIS Data Area

Attached Device(s):

SAS Array A Logical Drive 1 SAS Array B Logical Drive 2 Physical Drive (146 GB SAS) 1I:2 Physical Drive (0 MB SAS) 1I:3 Physical Drive (146 GB SAS) 1I:4 [ Top ] → 

[ Smart Array P410 in slot 4 ] → Device Error Report Device Status

Physical Drive (0 MB SAS) 1I:3  The physical drive has failed.

Logical Drive 1  Logical drive state: This logical drive has failed and cannot be used. All data on this logical drive has been lost.

[ Top ] → [ Smart Array P410 in slot 4 ] → Identify

Controller Configured Logical Drives 2 (0x02)

Configuration Signature 0xa051768b

RAM Firmware Revision 2.74

ROM Firmware Revision 2.74

Hardware Revision 0x02

Boot Block Revision 2.04

Drive Present Map 0x00000000

External Drive Map 0x00000000

Board ID 0x3243103c

Swapped Cable Flags 0x00

Non Disk Map 0x00000000

Bad Host RAM Addr 0x00

CPU Revision 0x48

PDPI Revision 0x00

EPIC Revision 0x01

WCXC Revision 0x00

Marketing Revision C Controller Flags 0x88

Position Controller Flag Status 3 Firmware supports 15 drives per SCSI bus Informational 7 Firmware supports the new big drive assignment maps (128 bits) as well as the big physical drive numbering (0x80+) Informational Host Flags 0x02 Expand Disable Code 0x00 Protocol Chip Count 0x01 Maximum Blocks 65535 (0x0000ffff) Controller Clock 0x0003fdaf Drives Per Bus 0 (0x00) Big Drive Present Map 0x0a 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 Position Device Status 1 Physical Drive (146 GB SAS) 1I:2 Informational 3 Physical Drive (146 GB SAS) 1I:4 Informational

 

Admin: Post moved as a new topic from HP ML150 G6 Fan Noise 

1 REPLY 1
SanjeevGoyal
HPE Pro

Re: HPE ML150 G6-Noisy Fan

Hello,

I would suggest you try the below steps as well as make sure server bios and all firmware should be updated with the latest.

Press F9 at startup
1. Advanced Options

2. Thermal Configuration
3. Choose "increased cooling"

F10 to confirm.....Save & exit

Then

Press F9 at startup

1. Advanced Options
2. Thermal Configuration
3. Choose "Optimal cooling"

F10 to confirm.....Save & exit

If you feel this was helpful please click the KUDOS! thumb below!   

Regards,


I am a HPE Employee

Accept or Kudo