ProLiant Servers (ML,DL,SL)
1745802 Members
3272 Online
108722 Solutions
New Discussion юеВ

HPE Prlliant DL380 G9 mv system from HBA mode to smart Array mode

 
fawzi1
Occasional Advisor

HPE Prlliant DL380 G9 mv system from HBA mode to smart Array mode

i have a functional test system on a Proliant DL380 G9. The DL380 is currently in HBA mode, meaning HDD connected to it will bypass the internal smart Array P840.

I would like to test this system using the internal P840, but i do not want to recreate the whole system again.

currently, when i reboot into smart storage setting and enable the P840, i get a warning of loosing all data on existing HDD. is there a way around this?

6 REPLIES 6
PiterParker
Valued Contributor

Re: HPE Prlliant DL380 G9 mv system from HBA mode to smart Array mode

Hi m8, 

 

As I am aware once array will start work in a raid mode it will need to reformat drives and put ourself pointers for data. 

Regards,

Piotr

fawzi1
Occasional Advisor

Re: HPE Prlliant DL380 G9 mv system from HBA mode to smart Array mode

thanks... but isn't there any "mixed" mode type where i can choose whether to use that p840 on an HDD or not?

it seems too captivating to have all HDD go thru it?

Torsten.
Acclaimed Contributor

Re: HPE Prlliant DL380 G9 mv system from HBA mode to smart Array mode

mixed mode (hba and raid) is available with newer controllers and per channel only. the layout of the disk is different in different modes, hence the new format.

Hope this helps!
Regards
Torsten.

__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.

__________________________________________________
No support by private messages. Please ask the forum!

If you feel this was helpful please click the KUDOS! thumb below!   
fawzi1
Occasional Advisor

Re: HPE Prlliant DL380 G9 mv system from HBA mode to smart Array mode

during setup, it says that you can configure it in mixed mode.  however, when i go to the configuration screen i only have 2 options.  HBA or RAID.

am i missing something that will enable the mixed mode? or is it a subset of the RAID mode?

 

PiterParker
Valued Contributor

Re: HPE Prlliant DL380 G9 mv system from HBA mode to smart Array mode

Hi m8, 

 

Could you check in specs? I can see 840 only supports HBA or RAID. If you have another array controller on the motheboard you could make one work in RAID mode and second one in HBA. 

http://www.intelligentservers.co.uk/content/HP-Smart-Array-P840-4GB-FBWC-12Gb-2-ports-Int-SAS-Controller-726897-B21-761880-001.pdf

Regards, 

Piotr

Torsten.
Acclaimed Contributor

Re: HPE Proliant DL380 G9 mv system from HBA mode to smart Array mode

"Newer" means Gen10 Controllers.

https://www.hpe.com/h20195/v2/getpdf.aspx/a00017196enw.pdf?ver=3.0

1 or 2 Gen9 controllers can do mixed mode too.

It means, the controller can do HBA mode at one channel, RAID mode at another channel - so this cannot be done in a single disk box, because this is a single channel.


Hope this helps!
Regards
Torsten.

__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.

__________________________________________________
No support by private messages. Please ask the forum!

If you feel this was helpful please click the KUDOS! thumb below!